Project MDACC No. XX-XXXX A/E Name A/E Project No. SECTION 09 68 00 CARPET
MDACC PROJECT NAME Issue Description Month, 00, 0000
PART 1 - GENERAL 0.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply to this Section. B. Specifications throughout all Divisions of the Project Manual are directly applicable to this Section, and this Section is directly applicable to them. 0.2 REFERENCE STANDARDS A. The latest published edition of a reference shall be applicable to this Project unless identified by a specific edition date. B. All reference amendments adopted prior to the effective date of this Contract shall be applicable to this Project. C. All materials, installation and workmanship shall comply with all applicable requirements and standards. 0.3 QUALITY ASSURANCE A. Carpet Surface Burning Characteristics: Provide carpet identical to that tested for the following fire performance characteristics, per test method indicated below, by UL or other testing and inspecting organizations acceptable to authorities having jurisdiction. Identify carpet with appropriate markings of applicable testing and inspecting organization. 1. 2. Test Method: DOC FF 1 70. Rating: Pass. B. Factory Runs: Provide Carpet from one factory run and one dye lot with colors and shades guaranteed to be uniform throughout the entire area run for type of carpet specified. C. Vermin and Dampproofness: Provide moth and vermin proofed carpet, compatible with installation over concrete slab on grade floors. 0.4 SUBMITTALS A. Shop Drawings: 1. Layout and seaming diagrams: a. b. c. B. Samples: Indicate pile or pattern direction and locations and types of edge strips. Indicate columns, doorways, enclosing walls or partitions, built in cabinets, and locations where cutouts are required in carpet. Show installation details at special conditions.
The University of Texas M. D. Anderson Cancer Center MS010107
CARPET 09 68 00 1 OF 5
MDACC Project No. XX-XXXX A/E Name A/E Project No. 1.
MDACC PROJECT NAME Issue Description Month, 00, 0000
Samples for verification purposes in manufacturer's standard size, showing full range of color, texture, and pattern variations expected. Prepare samples from same material to be used for the Work. Submit the following: a. b. c. d. 0.5 12 inch square samples of each type of carpet material required. Two (2) full-size samples of each carpet tile required. 12 inch long samples of each type exposed edge stripping and accessory item. 6 inch square samples of each type of carpet cushion.
DELIVERY, STORAGE AND HANDLING A. Deliver materials to Project Site in original factory wrappings and containers, labeled with identification of manufacturer, brand name, and lot number. B. Store materials in original undamaged packages and containers, inside well ventilated area protected from weather, moisture, soilage, extreme temperatures, and humidity. Lay flat, blocked off ground. Maintain minimum temperature of 68 degrees F (20 degrees C) at least three days prior to and during installation in area where materials are stored.
0.6
EXTRA MATERIALS A. Furnish extra materials matching products installed as described below, packaged with protective covering for storage and identified with labels describing contents. Deliver extra materials to Owner's storage location at The University of Texas, M. D. Anderson Cancer Center, Physical Plant, 7777 Knight Road.
1. 2.
Broadloom Carpet: Before installation begins, furnish quantity of full width for each type of material equal to 5 percent of amount installed. Carpet Tile: Before installation begins, furnish quantity of full size tiles for each type of material equal to 10 percent of amount installed. 0.7 PROJECT CONDITIONS A. Substrate Conditions: No condensation within 48 hours on underside of 4 foot by 4 foot polyethylene sheet, fully taped at perimeter to substrate. B. Substrate Conditions: pH of 9 or less when substrate wetted with potable water and pHydrion paper applied. 0.8 WARRANTY A. General Warranty: The special warranty specified in this Section shall not deprive the Owner of other rights the Owner may have under other provisions of the Contract Documents and shall be in addition to, and run concurrent with, other warranties made by the Contractor under requirements of the Contract Documents. B. Special Carpet Warranty: Submit a written warranty executed by carpet manufacturer and Installer agreeing to repair or replace carpet that does not meet requirements or that fails in materials or workmanship within the specified warranty period. Failures include, but are not limited to:
1.
Wear: Carpet materials shall evidence no more than 10 percent loss of face fiber. The University of Texas M. D. Anderson Cancer Center MS010107 CARPET 09 68 00 2 OF 5
MDACC Project No. XX-XXXX A/E Name A/E Project No. 2. normal use. 3. 4.
MDACC PROJECT NAME Issue Description Month, 00, 0000
Edge Raveling: Carpet material shall exhibit no edge ravel, snags, and runs under Delamination: Carpet materials shall not delaminate from primary or secondary backing. Shrinkage: Carpet materials shall show no shrinkage. C. Warranty Period: Five (5) years from date of Substantial Completion. PART 2 - PRODUCTS 0.1 GENERAL A. All materials shall meet or exceed all applicable referenced standards, federal, state and local requirements, and conform to codes and ordinances of authorities having jurisdiction. B. The notes and schedules on the Drawings establish manufacturer and model/design required for the Project. Provide the products listed unless Architect approves products of other manufacturer specifically for this Project. 0.2 MANUFACTURERS A. To establish standards of manufacture, operation, performance, and appearance, drawings specifications and are based on the specific manufacturer's products and color/patterns shown on the Drawings. If accepted in advance by the Architect, and provided compliance with requirements, products of other manufacturers may also be acceptable: 0.3 CARPET MATERIALS A. Provide the following carpeting materials at locations indicated:
1. 2.
Carpet Type 1: Modular Tiles; Interface "Tapestry Plus" Color; #2448 Babylon Carpet Type 2: Modular Tiles; Networx "Vector - 59487" Color; Coral Rose #87850 B. Provide the following carpeting materials at locations indicated:
1. 2. 3. 4. 5. 0.4
Carpet Type 1: Modular Tiles; Interface "Tapestry Plus" Color; #2448 Babylon Carpet Type 2: Modular Tiles; Interface "Tones Plus" Color; #3331 Tigris Carpet Type 3: Modular Tiles; Interface "Tones Plus" Color; #3326 Begonia Mauve Carpet Type 4: Modular Tiles; Collins & Aikman # 3261-O2MOC Carpet Type 5: Broadloom Carpet; Collins & Aikman # 3261-O2MOC ACCESSORIES A. Tackless Carpet Stripping: Water resistant plywood in strips, 3/8 inch or 9/32 inch thick, as required to match cushion thickness and in compliance with CRI 104, 11.3. B. Carpet Edge Guard: Extruded aluminum carpet edge similar to #416 by National Guard Products Inc., mill finish aluminum.
The University of Texas M. D. Anderson Cancer Center MS010107
CARPET 09 68 00 3 OF 5
MDACC Project No. XX-XXXX A/E Name A/E Project No.
MDACC PROJECT NAME Issue Description Month, 00, 0000
C. Seaming Cement: Hot melt adhesive tape or similar product recommended by carpet manufacturer for taping seams and butting cut edges at backing to form secure seams and to prevent pile loss at seams. D. Carpet Adhesive: Non-solvent based, water resistant, and nonstaining as recommended by carpet and carpet tile manufacturer to comply with flammability requirements for installed carpet and compatible with substrate. E. Trowelable Underlayments and Patching Compounds: Latex modified, portland cement based formulation provided or approved by floor covering manufacturer for applications indicated. PART 3 - EXECUTION 0.1 PREPARATION A. Clear away debris and scrape up cementitious deposits from concrete surfaces to receive carpet; apply sealer to prevent dusting. B. Patch holes and level to a smooth surface. If previous finish chemically stripped, reseal concrete. Seal powdery or porous surfaces with sealer recommended by carpet manufacturer. C. Patch holes and cracks. Sand to level. recommended by carpet manufacturer. Remove wax. Seal surface with sealer
D. Replace missing pieces of existing resilient flooring or patch to level. Cut out peaked sheet goods seams and fill with latex underlayment. E. Remove chemical finish on terrazzo; patch grout lines and cracks to level with latex underlayment. 0.2 INSTALLATION A. Installation shall meet or exceed all applicable federal, state and local requirements, referenced standards and conform to codes and ordinances of authorities having jurisdiction. B. All installation shall be in accordance with manufacturer's published recommendations. C. Dry fit sections of carpet prior to application of adhesive. D. Apply adhesive uniformly to substrate in accordance with manufacturer's instructions. Butt edges tight to form seams without gaps. E. Adhere perimeter tiles and partial tiles with a full spread of adhesive. Dry fit cut tiles and apply adhesive to tile back after tile has been cut. In corridor areas, use full tiles do...