We aren't endorsed by this school

ENTC 463 - MECHANICAL DESIGN APPLICATIONS II - Texas A&M Study Resources
  • 3 Pages ENTC463HW3
    ENTC463HW3

    School: Texas A&M

  • 32 Pages ENTC 463 Chapter 19 Lecture Notes-RK
    ENTC 463 Chapter 19 Lecture Notes-RK

    School: Texas A&M

    ENTC463 Chapter 19:Springs Chapter 19: Springs Agenda Finish Chapter 19: Springs Homework Set # 9 due Work problems if time permits Chapter 19: Springs Helical Compression Springs For stress calculations use the MEAN diameter of the wire.

  • 1 Page wormgear
    Wormgear

    School: Texas A&M

    WORMGEARING PROBLEM: 54 INPUT DATA Worm pitch diameter = 0.625 in Diametral pitch = 16 No. of worm threads = 2 No. of gear teeth = 100 Face width of gear = 0.313 in COMPUTED RESULTS Circular pitch of gear = 0.1963 in Axial pitch of worm = 0.1963 in L

  • 1 Page helicapy
    Helicapy

    School: Texas A&M

    HELICAL GEARS APPLICATION: POWER TRANSMISSION CAPACITY Initial Input Data: 2.500 in Enter: Face Width: F = nP = Input Speed: 1725 rpm Pd = Diametral Pitch: 9.66 NP = Number of Pinion Teeth: 20 NG = Number of Gear Teeth: 75 Computed data: Actual Outp

  • 25 Pages ENTC 463 Chapter 8-II Lecture Notes-RK
    ENTC 463 Chapter 8-II Lecture Notes-RK

    School: Texas A&M

    ENTC463 Chapter8:KinematicsofGears (continued) Chapter8:KinematicsofGears HelicalGearGeometry Left Hand Helix Right Hand Helix Chapter8:KinematicsofGears Forces on a Helical Gears Normal force between the mating teeth is defined as WN. To find

  • 16 Pages ENTC463Wire Rope
    ENTC463Wire Rope

    School: Texas A&M

    Wire Rope ENTC 463 Mechanical Design Application II Hoisting Elevator Ski lift, etc. D wire diameter, dw strand rope diameter, d pulley diameter, D Designation example : 1 x 6 x 19 d = 1.5 6 strands/rope 19 wires/strand Wire rope lays Regular

  • 39 Pages ENTC463Shaft Design
    ENTC463Shaft Design

    School: Texas A&M

    Shaft Design ENTC 463 Mechanical Design Applications II Next Thursday 4/3/2008 Meet @ Thompson 009B Allen to Hagan 2:20 to 3:00 PM Higginbotham to Winniford 3:00 to 3:35 PM ENTC 463 Mechanical Design Applications II ATTENTION: MMET Students, the

  • 23 Pages ENTC463Bevel Gears
    ENTC463Bevel Gears

    School: Texas A&M

    Bevel Gears ENTC 463 Mechanical Design Applications ENTC 463 HW #6 Bevel Gear Due 2/26/2008 Chapter 8 49 Chapter 10 15 Bevel Gears Straight Bevel Gear ZEROL Bevel Gear Spiral Bevel Gear Hypoid Gear Bevel Gears Objectives Power transmissi

  • 1 Page spurdes
    Spurdes

    School: Texas A&M

    DESIGN OF SPUR GEARS Initial Input Data: Input Power: Input Speed: Diametral Pitch: Number of Pinion Teeth: Desired Output Speed: Computed number of gear teeth: Enter: Chosen No. of Gear Teeth: Computed data: Actual Output Speed: Gear Ratio: Pitch Di

  • 43 Pages ENTC463RollingBearings
    ENTC463RollingBearings

    School: Texas A&M

    Bearings ENTC 464 Mechanical Design Applications ENTC 463 HW#8, due 3/4/2008 Chapter 14 4, 9 Bearings Bearings Objectives Support load Allow relative motion (friction) Type of loads Radial direction (radial load) Axial direction (thrust

  • 50 Pages ENTC 463 Chapter 22 Lecture Notes-RK
    ENTC 463 Chapter 22 Lecture Notes-RK

    School: Texas A&M

    ENTC463 Chapter 22:Motion Control, Clutches and Brakes Chapter 22: Motion Control: Clutches and Brakes Agenda Start on Chapter 22 Chapter 22: Motion Control: Clutches and Brakes What is the difference between a clutch and a brake? Clutch a

Back to course listings