Homework 5

Homework 5 - ME 3365 Introduction to Design Homework 5(Due...

Info iconThis preview shows pages 1–4. Sign up to view the full content.

View Full Document Right Arrow Icon
Background image of page 1

Info iconThis preview has intentionally blurred sections. Sign up to view the full version.

View Full DocumentRight Arrow Icon
Background image of page 2
Background image of page 3

Info iconThis preview has intentionally blurred sections. Sign up to view the full version.

View Full DocumentRight Arrow Icon
Background image of page 4
This is the end of the preview. Sign up to access the rest of the document.

Unformatted text preview: ME 3365 Introduction to Design Homework 5 (Due: March 15, 2008) l. A 2 1/2 X 2 V2 -in sleeve bearing uses grade 20 lubricant. The axial-groove sump has a steady state temperature of HOT. The shaft journal has a diameter of 2.5 in with a unilateral tolerance of -0.001 in. The bushing bore has a diameter of 2.504 in with a unilateral tolerance of 0.001 in. The journal speed is 1120 revfmin and the radial load is 13 00 lbf. Estimate (a) The magnitude and location of the minimum oil-film thickness. (b) The eccentricity. (e) The coefficient of friction. (d) The power loss rate. (e) Both the total and side oil-flow rates. (f) The maximum oil—film pressure and its angular location. (g) The terminating position of the oil film (h) The average temperature of the side flow. (i) The oil temperature at the terminating position of the oil film. 2. A compound gear train as shown in the following figure, Gear 1 has 24 teeth and Gear 2 has 7’0 teeth of diametral pitch of 4. Gear 3 has 30 teeth and Gear 4 has 50 teeth of diamerral pitch of 3. Gear 1 turns 12 rpm in clockwise direction. (a) Computer the speed and direction of the shaft carrying Gear 4. (b) Find the torque at Shaft c if the input horsepower at Shaft a is 50? Shaft 13 Gear 1 Gear 2 Gear 3 Gear 4 ©KMPH Page 1 of 1 Rev, 4f8i'2008 u "I TEXAS TECH UNIVERSITY Sheet Of ‘__' Department of Mechanical Engineering~ By Date N: 1120 Yen/WW :6 2 2'5 i’ gang loonan Pén‘fim mam Pmnmwj’e'rs. (0‘3 9‘5"" £35 12%; “m, ~= 0'4‘82. ..‘. ha .2: 0‘422-(0‘061) : 0'000c364 bu Pfcw.%ra\2fil7’ ¢ : Béo (Q 6 T; (1ka .2 o~ooz~ 0000964 -= 0‘00104” (G) 9mm I243, ‘1 TEXAS TECH UNIVERSITY Sheet m“ Of 53, Department of Mechanical Engineering By _ Date (a) 'T 2—- *fw‘f a: o-oaeaijPz—S) “:2 ‘3 " 84 “a; ' 1W ZWT biotin) N ("rev/- H :— ._ 2m a N (v20 _ .(an 993905-310 (mm) engine) 9336 Go «1 @‘124 BTU/3.1.; ww‘ Ce) em in, a TC- -.‘. Q = ‘4‘“16 Li»26)C¢‘0029< 66>G‘JQ i 5 w- 'T' ~ .g {I Ch) 72W; ~— T5+ fig: Z; “of 2:1; : 12—3‘aor; 0’) To 7' Ts+ M” 1110+ 2’?‘8 : i‘37°85i= 1:: :.. '3' TEXAS TECH UNIVERSITY Sheet Of Department of Mechanical Engineering 33, Date ...
View Full Document

This note was uploaded on 04/15/2008 for the course ME 3365 taught by Professor Khandakar during the Spring '08 term at Texas Tech.

Page1 / 4

Homework 5 - ME 3365 Introduction to Design Homework 5(Due...

This preview shows document pages 1 - 4. Sign up to view the full document.

View Full Document Right Arrow Icon
Ask a homework question - tutors are online