{[ promptMessage ]}

Bookmark it

{[ promptMessage ]}

Chapter_04

# Chapter_04 - GUS CHAPTER 4 Exercises E4.1 The voltage...

This preview shows pages 1–4. Sign up to view the full content.

85 CHAPTER 4 Exercises E4.1 The voltage across the circuit is given by Equation 4.8: ) / exp( ) ( RC t V v i C = in which is the initial voltage. At the time 1% for which the voltage reaches 1% of the initial value, we have ) / exp( 01 . 0 % 1 = Taking the natural logarithm of both sides of the equation, we obtain / 605 . 4 ) 01 . 0 ln( % 1 = = Solving and substituting values, we find 1% = 4.605 RC = 23.03 ms. E4.2 The exponential transient shown in Figure 4.4 is given by ) / exp( ) ( τ s = Taking the derivative with respect to time, we have ) / exp( ) ( dt dv = Evaluating at = 0, we find that the initial slope is . / S Because this matches the slope of the straight line shown in Figure 4.4, we have shown that a line tangent to the exponential transient at the origin reaches the final value in one time constant. E4.3 (a) In dc steady state, the capacitances act as open circuits and the inductances act as short circuits. Thus the steady-state (i.e., approaching infinity) equivalent circuit is: From this circuit, we see that A. 2 = a Then ohm’s law gives the voltage as V. 50 = = Ri

This preview has intentionally blurred sections. Sign up to view the full version.

View Full Document
86 (b) The dc steady-state equivalent circuit is: Here the two 10- resistances are in parallel with an equivalent resistance of 1/(1/10 + 1/10) = 5 . This equivalent resistance is in series with the 5- resistance. Thus the equivalent resistance seen by the source is 10 , and A. 2 10 / 20 1 = = i Using the current division principle, this current splits equally between the two 10- resistances, so we have A. 1 3 2 = = E4.4 (a) ms 1 100 / 1 . 0 / 2 = = = R L τ (b) Just before the switch opens, the circuit is in dc steady state with an inductor current of A. 5 . 1 / 1 = V s This current continues to flow in the inductor immediately after the switch opens so we have A 5 . 1 ) 0 ( = + . This current must flow (upward) through 2 so the initial value of the voltage is V. 150 ) 0 ( ) 0 ( 2 = + = + v (c) We see that the initial magnitude of ( t ) is ten times larger than the source voltage. (d) The voltage is given by ) 1000 exp( 150 ) / exp( ) ( 1 = = Let us denote the time at which the voltage reaches half of its initial magnitude as H . Then we have ) 1000 exp( 5 . 0 = Solving and substituting values we obtain ms 6931 . 0 ) 2 ln( 10 ) 5 . 0 ln( 10 3 3 = = =
87 E4.5 First we write a KCL equation for . 0 t = + + dx x v L R 0 2 0 ) ( 1 ) ( Taking the derivative of each term of this equation with respect to time and multiplying each term by , we obtain: 0 ) ( ) ( = + dt dv The solution to this equation is of the form: ) / exp( ) ( τ K = in which s 2 . 0 / = = is the time constant and is a constant that must be chosen to fit the initial conditions in the circuit. Since the initial ( = 0+) inductor current is specified to be zero, the initial current in the resistor must be 2 A and the initial voltage is 20 V: = = + 20 ) 0 ( Thus, we have ) / exp( 20 ) ( = ) / exp( 2 / i = = [] ) / exp( 2 2 ) / exp( 20 2 1 ) ( 1 ) ( 0 0 τ τ τ = = = E4.6 Prior to = 0, the circuit is in DC steady state and the equivalent circuit is Thus we have (0-) = 1 A. However the current through the inductor cannot change instantaneously so we also have (0+) = 1 A. With the switch open, we can write the KVL equation: 100 ) ( 200 ) ( = + di The solution to this equation is of the form ) / exp( ) ( 2 1 + = in which the time constant is ms. 5 200 / 1 = =

This preview has intentionally blurred sections. Sign up to view the full version.

View Full Document
This is the end of the preview. Sign up to access the rest of the document.

{[ snackBarMessage ]}

### Page1 / 35

Chapter_04 - GUS CHAPTER 4 Exercises E4.1 The voltage...

This preview shows document pages 1 - 4. Sign up to view the full document.

View Full Document
Ask a homework question - tutors are online