F08 314 HW07 all

# F08 314 HW07 all - EECS 314 Fall 2008 Homework set 7...

This preview shows pages 1–4. Sign up to view the full content.

EECS 314 Fall 2008 Homework set 7 Student’s name ___________________________ Discussion section # _______ (Last, First, write legibly, use ink) (use ink) Instructor is not responsible for grading and entering scores for HW papers lacking clear information in the required fields above © 2008 Alexander Ganago Page 1 of 2 Scores for the HW set: Problem 1 2 3 4 5 6 7 Total Score Problem 1 Voltage division in the phasor world The Big Picture To solve this problem, you should use the formulas for impedances Z L = j " # " L and Z C = 1 j " " C at different frequencies ω = 2 π f . The units: if capacitance is in farads, inductance in henry, and frequency ω in rad/sec, then the impedance is in ohms. If f is in kHz, then 2 π f is in krad/sec. In all equations, the impedances are used exactly as resistances, according to the rules of complex algebra. You will obtain expressions such as Z = (5 + j 2) Ω , and V = V MAX ∠α where V MAX is the peak voltage. The Assignment Consider the circuit shown on the diagram with the following component values: R = 100 Ω C = 150 nF L = 3 mH V S = 25 cos( ω t) V . Assume sinusoidal steady-state conditions. Consider two frequencies: 1 kHz and 5 kHz. Part 1 2 3 Total

This preview has intentionally blurred sections. Sign up to view the full version.

View Full Document
EECS 314 Fall 2008 Homework set 7 Student’s name ___________________________ Discussion section # _______ (Last, First, write legibly, use ink) (use ink) Instructor is not responsible for grading and entering scores for HW papers lacking clear information in the required fields above © 2008 Alexander Ganago Page 2 of 2 Problem 1, continued Part 1 (10 points) Use the component values on page 1; calculate the impedances in ohms. Show your work for 2 kHz. Write the results in the table below. Frequency Z L Z C 2 kHz 10 kHz Part 2 (30 points) Calculate the peak amplitude of each current in mA and each voltage in V and write your results in the table below: Frequency, kHz Capacitor current I C Capacitor voltage V C Inductor current I L Inductor voltage V L 2 10 Briefly discuss how the increase of frequency affects the magnitude of each voltage and current. Show your work on additional pages.
EECS 314 Fall 2008 Homework set 7 Student’s name ___________________________ Discussion section # _______ (Last, First, write legibly, use ink) (use ink) Instructor is not responsible for grading and entering scores for HW papers lacking clear information in the required fields above © 2008 Alexander Ganago Page 1 of 2 Problem 2 Maximal power transfer to the load in AC circuits The Big Picture In the phasor form, the voltage across a circuit element and the current through it are ˆ V = V max " # V and ˆ I = I max " I , where V max and I max are the peak amplitudes of the sinusoidal functions, and " V and " I are the phase angles. The complex power absorbed by the circuit element is defined as

This preview has intentionally blurred sections. Sign up to view the full version.

View Full Document
This is the end of the preview. Sign up to access the rest of the document.

## This note was uploaded on 10/25/2008 for the course EECS 314 taught by Professor Ganago during the Fall '07 term at University of Michigan.

### Page1 / 20

F08 314 HW07 all - EECS 314 Fall 2008 Homework set 7...

This preview shows document pages 1 - 4. Sign up to view the full document.

View Full Document
Ask a homework question - tutors are online