hw04sol

# hw04sol - ECE 315 Homework 4 Solution Fall 2007 1(Bipolar...

This preview shows pages 1–3. Sign up to view the full content.

ECE 315 Homework 4 Solution Fall 2007 1. (Bipolar transistor operating regions) For the following silicon BJT conditions, state the operating region (a) NPN with V BE = 0.7V and V CE = 0.0V in common-emitter notation. (2 pts) Notice that “common” means that the other two terminals use it as a voltage reference (often ground). You need to translate to the junction voltage to find the operating region. This problem helps you get familiar with the different BJT circuit configurations. V BE = 0.7 V forward-biased emitter-base junction V CE = 0 V V BC = V BE – V CE = 0.7 V forward-biased collector-base junction SATURATION operation (b) NPN with V BE = 0.9V and V CE = 2.0V in common-emitter notation. (2 pts) V BE = 0.9 V forward-biased emitter-base junction V CE = 2.0 V V BC = -1.1 V reverse-biased collector-base junction FORWARD ACTIVE operation (c) NPN with V BC = 0.7V and V EC = - 2.0V in common-collector notation. (2 pts) V BC = 0.7 V forward-biased collector-base junction V EC = -2.0 V V BE = V BC – V EC = 2.7 V forward-biased emitter-base junction SATURATION operation (d) NPN with V EB = 0.3V and V CB = 2.0V in common-base notation. (2 pts) V EB = 0.3 V reverse-biased emitter-base junction V CB = 2.0 V reverse-biased collector-base junction CUTOFF operation (e) PNP with V BE = - 0.9V and V CE = - 2.0V in common-emitter notation. (2 pts) V BE = -0.9 V forward-biased emitter-base junction V CE = -2.0 V V BC =1.1 V reverse-biased collector-base junction FORWARD ACTIVE operation (f) PNP with V EB = 0.9V and V CB = - 2.0V in common-base notation. (2 pts) V EB = 0.9 V forward-biased emitter-base junction V CB = -2.0 V reverse-biased emitter-base junction FORWARD ACTIVE operation 1

This preview has intentionally blurred sections. Sign up to view the full version.

View Full Document
2. (Large-signal and small-signal BJT models) For a NPN BJT, (a) Draw the large-signal Ebers-Moll model with the current gain parameters of α F and R (pay attention to the direction of the dependent current source) (5 pts) (b) If we have designed the BJT with a large current gain by N E >>N B >>N C and W B <<L n , denote the main current components (in terms of electron-hole drift-diffusion- recombination terms) in the forward active mode for I E , I B and I C . (6 pts) From the electron-hole drift-diffusion-recombination point of view: For NPN BJT in forward active mode: I E is dominated by the injection of electrons from the emitter into the base, which is equivalent to the minority electron diffusion current at the base edge of the emitter-base junction I En = (qD n n Bpo A E /W B ) × [exp{qV BE /kT} – 1] This can be obtained by assuming W B << L n , N B >> N C linearly decreasing base minority electron density from n po exp (qV BE /kT) at the base edge of emitter-base junction to n po exp (qV BC /kT) at the base edge of collector-base junction; the latter term is assumed to be pratically 0 due to reverse-bias V BC . I
This is the end of the preview. Sign up to access the rest of the document.

{[ snackBarMessage ]}

### Page1 / 8

hw04sol - ECE 315 Homework 4 Solution Fall 2007 1(Bipolar...

This preview shows document pages 1 - 3. Sign up to view the full document.

View Full Document
Ask a homework question - tutors are online