CISCO CMD - POTABLE CISCO COMMAND 1- The Command Line...

Info iconThis preview shows pages 1–9. Sign up to view the full content.

View Full Document Right Arrow Icon

Info iconThis preview has intentionally blurred sections. Sign up to view the full version.

View Full DocumentRight Arrow Icon

Info iconThis preview has intentionally blurred sections. Sign up to view the full version.

View Full DocumentRight Arrow Icon

Info iconThis preview has intentionally blurred sections. Sign up to view the full version.

View Full DocumentRight Arrow Icon

Info iconThis preview has intentionally blurred sections. Sign up to view the full version.

View Full DocumentRight Arrow Icon
This is the end of the preview. Sign up to access the rest of the document.

Unformatted text preview: POTABLE CISCO COMMAND 1- The Command Line Interface 2- Configuring Switch 3- Configuring VLAN 4- Configuring Router 5- Static Routing 6- Configuring IP Routing Protocol RIP IGRP EIGRP OSPF 7- Configuring Access Control List (ACL) 8- Network Address Translation (NAT) 9- Dynamic Host Control Protocol (DHCP) 10-WAN-Leased Line Connection (HDLC, PPP) 11- Frame Relay Connection 12- Network Administration and troubleshooting CDP Ping Traceroute Telnet command 13- Restoring and Backing up Cisco Router 14- Password Recovery Procedure Author: Dinesh Kumar Kusta MIT- EAST, Wipro Infotech CISCO COMMANDS SHORTCUT FOR ENTERING COMMANDS USING QUESTION MARK FOR HELP EXIT COMMAND DISABLE COMMAND LOGOUT COMMAND SETUP MODE KEYBOARD HELP HISTORY COMMANDS SHOW COMMAND CONFIGURING SWITCH COMMAND MODE VERIFY COMMAND RESETTING SWITCH CONFIGURATION SETTING HOST NAME FOR SWITCH SETTING PASSWORD SETTING CONSOLE PASSWORD SETTING TELNET PASSWORD SETTING AUXILIRY PASSWORD SETTING IP ADDRESS AND DEFAULT GATEWAY 2960Switch(config)#interface vlan1 2960Switch(config-if)#ip address IP_Address Subnet_mask 2960Switch(config-if)#exit 2960Switch(config)#ip default-gateway Routers_IP_address SETTING INTERFACE DESCRIPTION 2960Switch(config)#interface ethernet/ fastethernet/ gigabit 0/port_no 2960Switch(config)#interface fastethernet 0/1 2960Switch(config-if)#description type_description 2960Switch(config-if)#description Finance VLAN SETTING DUPLEX Enters the virtual interface for VLAN 1, the default VLAN on the switch Sets the IP address and netmask to allow for remote access Allows IP information an exit past the local network Enters interface configuration mode Adds a description of the interface SETTING SPEED MANAGING MAC ADDRESS TABLE CONFIGURING STATIC MAC ADDRESS 2960Switch(config)#mac-address-table static MAC_address vlan VLAN_no interface type slot_no/port_no 2960Switch(config)#mac-address-table static aaaa.aaaa.aaaa vlan 1 interface fastethernet 0/1 2960Switch(config)#no mac-address-table static aaaa.aaaa.aaaa vlan 1 interface fastethernet 0/1 SWITCH PORT SECURITY Sets a permanent address to port fastethernet 0/1 in VLAN Removes the permanent address to port fastethernet 0/1 in VLAN 1 Switch(config)#interface fastethernet/gigabit 0/port_no Switch(config)#interface fastethernet 0/1 Switch(config-if)#switchport port-security Switch(config-if)#switchport port-security maximum value Switch(config-if)#switchport port-security maximum 4 Switch(config-if)#switchport port-security mac-address MAC_address Switch(config-if)#switchport port-security mac-address 1234.5678.90ab Moves to interface configuration mode. Enables port security on the interface. Sets a maximum limit of four MAC addresses that will be allowed on this port. The default is 132, range is 1-132....
View Full Document

Page1 / 63

CISCO CMD - POTABLE CISCO COMMAND 1- The Command Line...

This preview shows document pages 1 - 9. Sign up to view the full document.

View Full Document Right Arrow Icon
Ask a homework question - tutors are online