{[ promptMessage ]}

Bookmark it

{[ promptMessage ]}

heattreatment - Changing the Properties of Steels Steels...

Info icon This preview shows page 1. Sign up to view the full content.

View Full Document Right Arrow Icon
This is the end of the preview. Sign up to access the rest of the document.

Unformatted text preview: Changing the Properties of Steels Steels Can be heat treated to alter properties by either: Heating and rapid cooling (quenching) Heating and slow cooling Quenching The steels shown in blue on the following slide can be heat treated to harden them by quenching. Metals Ferrous metals Steels Plain carbon steels Low carbon steels Medium carbon steels High carbon steels Low alloy steels High alloy steels Stainless & Tool steels Non-ferrous metals Cast Irons Grey Iron White Iron Malleable & Ductile Irons Hardening Temperatures The temperatures for hardening depend on the carbon content. Plain carbon steels below 0.4% will not harden by heat treatment. The temperature decreases from approx 820 deg C as carbon content increases from 0.4% up to 0.8%, where temperature is approx 780 deg C. Above 0.8% the temperature remains constant at 780 deg C. Austenite This is the structure of irons and steels at high temperatures (over 800 deg C). For quench hardening all the material must start as Austenite. Quenching causes the Austenite to be partially or totally transformed to Martensite. Martensite Only formed by very rapid cooling from the austenitic structure. Needs to be above the Critical Cooling Rate. The needle­like structure of martensite, the white areas are retained austenite. Hardenability This is dependent upon the chemical composition of the steel alloy. The addition of Nickel, Chromium and Molybdenum will slow the transformation to other phases and allow more martensite to form. Most heat treatable steels are alloys rather than plain carbon steels. Quenching Media Four commonly used quenching media: Brine – the fastest cooling rate Water – moderate cooling rate Oil – slowest cooling rate Gas – used in automatic furnaces, usually liquid nitrogen, can be very fast cooling. Too rapid cooling can cause cracking in complex and heavy sections. Depth of Hardening Due to the mass effect, not all the section of a large component may be hardened due to too slow a cooling rate. This may leave a soft core, or in extreme cases prevent hardening altogether. The Heat Treatment Process “Pearlite” (ductile) BCC + Fe3C with different microstructures “Martensite” (brittle) How you heat treat makes all the difference to the steel you get Tempering The brittleness of martensite makes hardened steels unsuitable for most applications. This requires the steel to be tempered by re­heating to a lower temperature to reduce the hardness and improve the toughness. This treatment converts some of the martensite to another structure called bainite. Tempering Temperatures Slow Cooling Rate Processes Normalising Annealing Spheroidising Stress­relief annealing Normalising 1. 2. 3. 4. Heat to Upper Critical Temperature, at which point the structure is all Austenite Cool slowly in air. Structure will now be fine equi­axed pearlite. Used to restore the ductility of cold or hot worked materials whilst retaining other properties. Annealing 1. 2. 3. 4. Heat to above Upper Critical Temperature, at which point the structure is all Austenite Cool very slowly in the furnace. Structure will now be large­grained pearlite. Used to improve the properties of cast and forged steels prior to machining. Grain Growth A glass vial containing a liquid that foams. Shaking results in a fine foam, which slowly coarsens with time. The coarsening process is somewhat analogous to grain growth in solids. The same vial, after allowing some time for the foam to coarsen. The process occurs in order to reduce the surface per unit volume. Spheroidising 1. 2. 3. 4. Heat to just below Lower Critical Temperature. (about 650­700 deg C) Cool very slowly in the furnace. Structure will now be spheroidite, in which the Iron Carbide has ‘balled up’. Used to improve the properties of medium and high carbon steels prior to machining or cold working. 1. 2. 3. 4. Heat to below Upper Critical Temperature to cause recrystallisation Cool very slowly in the furnace. Structure will now be equi­axed pearlite. Used to maximise the ductility of low carbon steels and other materials after cold working. Process (stress­relief) Annealing Cold Working Cold roll to “pancake” grains Increases hardness and strength at the expense of ductility. ...
View Full Document

{[ snackBarMessage ]}

What students are saying

  • Left Quote Icon

    As a current student on this bumpy collegiate pathway, I stumbled upon Course Hero, where I can find study resources for nearly all my courses, get online help from tutors 24/7, and even share my old projects, papers, and lecture notes with other students.

    Student Picture

    Kiran Temple University Fox School of Business ‘17, Course Hero Intern

  • Left Quote Icon

    I cannot even describe how much Course Hero helped me this summer. It’s truly become something I can always rely on and help me. In the end, I was not only able to survive summer classes, but I was able to thrive thanks to Course Hero.

    Student Picture

    Dana University of Pennsylvania ‘17, Course Hero Intern

  • Left Quote Icon

    The ability to access any university’s resources through Course Hero proved invaluable in my case. I was behind on Tulane coursework and actually used UCLA’s materials to help me move forward and get everything together on time.

    Student Picture

    Jill Tulane University ‘16, Course Hero Intern