vg200_cfg - Configuring the Cisco IOS MGCP Gateway Document...

Info iconThis preview shows pages 1–3. Sign up to view the full content.

View Full Document Right Arrow Icon
Configuring the Cisco IOS MGCP Gateway Document ID: 42105 Introduction Prerequisites Requirements Components Used Conventions Tasks to Perform Step-by-Step Summary Configurations Troubleshooting the IOS MGCP Gateway NetPro Discussion Forums - Featured Conversations Related Information Introduction This document: Guides you through a simple Media Gateway Control Protocol (MGCP) configuration Presents only the minimum commands required to build a configuration that works for a router with two Foreign Exchange Office (FXO) and two Foreign Exchange Station (FXS) ports Note: The instructions in this document work for a Cisco Voice Gateway 200 (VG200) and Cisco 2600 and 3600 series routers that run Cisco IOS® Software Release 12.1(5)T and later. Refer to the Cisco IOS software documentation for supported software releases of other Cisco IOS MGCP gateways. Symptoms: You can potentially encounter this list of symptoms when you configure Cisco CallManager with Cisco IOS MGCP gateways with analog FXO and FXS ports: The MGCP gateway does not register with Cisco CallManager. Refer to MGCP Gateway Registration Failure with Cisco CallManager. Caller ID does not work on FXO ports. This is because caller ID is not supported with FXO ports when configured for MGCP. Configure the gateway in H.323 mode instead. Overhead paging locks up FXO ports during hookflash unless users go completely off-hook. Shut followed by No shut resets the port. This is related to Cisco bug ID CSCef62275 ( registered customers only ) when fixed in Cisco IOS Software Release 12.3(14)T and later. This document is Part 2 of a six-document set: Configuring Cisco CallManager with IOS MGCP Gateways (Analog FXO, FXS Ports) Configuring the Cisco IOS MGCP Gateway Configure MGCP Gateway and FXO/FXS Ports on a Cisco CallManager Server Verify and Troubleshoot the Cisco IOS MGCP Gateway Sample of Debug MGCP Packets Monitor, Reset, and Delete MGCP Gateways for Cisco CallManager
Background image of page 1

Info iconThis preview has intentionally blurred sections. Sign up to view the full version.

View Full DocumentRight Arrow Icon
Prerequisites Requirements Cisco recommends that you have knowledge of these topics: A Cisco IOS gateway that runs a Cisco IOS software release that supports MGCP with Cisco CallManager Cisco VG200 Note: There are other Cisco IOS software release trains that support MGCP on Cisco routers. Cisco IOS Software Release 12.1XM is one example. Caution: The syntax for some of the MGCP commands is different in other Cisco IOS software releases. Refer to the documentation for your configuration to determine the syntax that is required. Components Used The information in this document is based on these software and hardware versions: 1 * Cisco VG200 / 2 X FXS / 2 X FXO / 1 Fast Ethernet 10/100 port; Cisco IOS Software Release 12.1(5)T 1 * Cisco CallManager 3.0(5a) that runs on an MCS7835 2 * Analog handsets 2 * Cisco 7960 IP phones Refer to Cisco Unified CME and Cisco IOS Software Version Compatibility Matrix for recommended compatibility software releases between Cisco CallManager and the Cisco IOS gateway. Note:
Background image of page 2
Image of page 3
This is the end of the preview. Sign up to access the rest of the document.

This note was uploaded on 08/08/2011 for the course CISCO 1232 taught by Professor Jack during the Spring '11 term at American International.

Page1 / 9

vg200_cfg - Configuring the Cisco IOS MGCP Gateway Document...

This preview shows document pages 1 - 3. Sign up to view the full document.

View Full Document Right Arrow Icon
Ask a homework question - tutors are online