CCNA-PC-2 - CCNA Practice Certification Exam 2 CCNA Exploration Accessing the WAN(Version 4.0 1 Refer to the exhibit The exhibit shows simplified

Info iconThis preview shows pages 1–3. Sign up to view the full content.

View Full Document Right Arrow Icon
CCNA Practice Certification Exam # 2- CCNA Exploration: Accessing the WAN (Version 4.0) 1. Refer to the exhibit. The exhibit shows simplified protocol data units from different OSI model layers. Which three statements are true about the PDUs and the encapsulation process? (Choose three.) PDU #1 is a frame. PDU #2 is an application layer PDU PDU #3 is a segment. PDU #4 is a transport layer PDU. The order in which these PDUs are created during the encapsulation process is 3, 4, 1, 2. The order in which these PDUs are created during the encapsulation process is 2, 1, 4, 3. 2. Which three application layer protocols use TCP? (Choose three.) SMTP FTP SNMP HTTP TFTP DHCP 3. Which two application layer protocols use the UDP protocol? (Choose two.) Telnet SNMP SMTP SQL TFTP 4. What are two functions that occur at the Internet layer of the TCP/IP model? (Choose two.) establishment of logical connections between source and destination hosts end-to-end flow control determination of best paths through the network definition of the procedures used to interface with the network hardware packet switching Layer 5 and Layer 6 OSI model functions 5. Refer to the exhibit. All ports on switch A are in the sales VLAN and all ports on switch B are in the accounting VLAN. How many broadcast domains and how many collision domains exist in the exhibited network? (Choose two.) 3 collision domains 3 broadcast domains 5 broadcast domains 9 collision domains 10 collision domains 13 collision domains 6. A high-end Catalyst switch that supports both ISL and 8 02.1Q is to be connected by a link that will carry all VLAN traffic to a Catalyst 2960 LAN switch. What two commands are required to configure an interface on the high-end Catalyst switch to carry traffic from all VLANs to the Catalyst 2960 switch? (Choose two.) Switch(config-if)# vlan all Switch(config-if)# switchport access vlan 30 Switch(config-if)# switchport access vlan all Switch(config-if)# switchport mode trunk Switch(config-if)# switchport trunk encapsulation dot1q
Background image of page 1

Info iconThis preview has intentionally blurred sections. Sign up to view the full version.

View Full DocumentRight Arrow Icon
Switch(config-if)# switchport trunk encapsulation isl 7. Refer to the exhibit. Based on the exhibited configuration and output, what would be the result of this command: Sw1# telnet 192.16 8 .1.10 All packets will be dropped. The Telnet session will succeed. An error message that says “Session terminated” will appear. An error message that says “Password required, but none set” will appear. 8 . Refer to the partial device configuration that is exhibited. For which network topology is the configuration appropriate? RtrA(config)# interface fastethernet 0/0 RtrA(config-if)# no shutdown RtrA(config-if)# interface fastethernet 0/0.1 8 RtrA(config-subif)# encapsulation dot1q 1 8 RtrA(config-subif)# ip address 10.1.1 8 .1 255.255.255.0 RtrA(config-subif)# interface fastethernet 0/0.44 RtrA(config-subif)# encapsulation dot1q 44 RtrA(config-subif)# ip address 10.1.44.1 255.255.255.0 RtrA(config-subif)# interface fastethernet 0/0.22 RtrA(config-subif)# encapsulation dot1q 22
Background image of page 2
Image of page 3
This is the end of the preview. Sign up to access the rest of the document.

This note was uploaded on 08/30/2011 for the course COMPUTER computer taught by Professor Ms during the Spring '10 term at Oxford University.

Page1 / 11

CCNA-PC-2 - CCNA Practice Certification Exam 2 CCNA Exploration Accessing the WAN(Version 4.0 1 Refer to the exhibit The exhibit shows simplified

This preview shows document pages 1 - 3. Sign up to view the full document.

View Full Document Right Arrow Icon
Ask a homework question - tutors are online