7.4.2 Lab -.docx - Lab Implement DHCPv4 Topology Addressing...

This preview shows page 1 - 3 out of 6 pages.

Lab - Implement DHCPv4 Topology Addressing Table Device Interface IP Address Subnet Mask Default Gateway R1 G0/0/0 10.0.0.1 255.255.255.252 N/A R1 G0/0/1 N/A N/A N/A R1 G0/0/1.100 192.168.1.1255.255.255.192N/A R1 G0/0/1.200 192.168.1.65255.255.255.224N/A R1 G0/0/1.1000 N/A N/A N/A R2 G0/0/0 10.0.0.2 255.255.255.252 N/A R2 G0/0/1 192.168.1.97255.255.255.240N/AS1 VLAN 200 192.168.1.66255.255.255.224192.168.1.65S2 VLAN 1 192.168.1.98255.255.255.240192.168.1.97PC-A NIC DHCP DHCP DHCP PC-B NIC DHCP DHCP DHCP VLAN Table VLAN Name Interface Assigned 1 N/A S2: F0/18 100 Clients S1: F0/6 200 Management S1: VLAN 200 999 Parking_Lot S1: F0/1-4, F0/7-24, G0/1-2 1000 Native N/A Objectives Part 1: Build the Network and Configure Basic Device Settings Part 2: Configure and verify two DHCPv4 Servers on R1 Part 3: Configure and verify a DHCP Relay on R2 ©2017 - 2019 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 1of 6
Lab - Implement DHCPv4 Background / Scenario The Dynamic Host Configuration Protocol (DHCP) is a network protocol that lets network administratorsmanage and automate the assignment of IP addresses. Without DHCP for IPv4, the administrator mustmanually assign and configure IP addresses, preferred DNS servers, and default gateways. As the networkgrows in size, this becomes an administrative problem when devices are moved from one internal network toanother. In this scenario, the company has grown in size, and the network administrators can no longer assign IPaddresses to devices manually. Your job is to configure the R1 router to assign IPv4 addresses on twodifferent subnets. Note: The routers used with CCNA hands-on labs are Cisco 4221 with Cisco IOS XE Release 16.9.4(universalk9 image). The switches used in the labs are Cisco Catalyst 2960s with Cisco IOS Release 15.2(2)(lanbasek9 image). Other routers, switches, and Cisco IOS versions can be used. Depending on the modeland Cisco IOS version, the commands available and the output produced might vary from what is shown inthe labs. Refer to the Router Interface Summary Table at the end of the lab for the correct interface identifiers.Note: Ensure that the routers and switches have been erased and have no startup configurations. If you areunsure contact your instructor. Required Resources 2 Routers (Cisco 4221 with Cisco IOS XE Release 16.9.4 universal image or comparable) 2 Switches (Cisco 2960 with Cisco IOS Release 15.2(2) lanbasek9 image or comparable) 2 PCs (Windows with a terminal emulation program, such as Tera Term) Console cables to configure the Cisco IOS devices via the console ports Ethernet cables as shown in the topology Instructions Part 1: Build the Network and Configure Basic Device Settings ***Answer the questions with __________***In Part 1, you will set up the network topology and configure basic settings on the PC hosts and switches.

  • Left Quote Icon

    Student Picture

  • Left Quote Icon

    Student Picture

  • Left Quote Icon

    Student Picture