A 813 _ A 813M _ 95 ;QTGXMY9BODEZTS1SRUQ_

A 813 _ A 813M _ 95 ;QTGXMY9BODEZTS1SRUQ_ - Designation: A...

Info iconThis preview shows pages 1–2. Sign up to view the full content.

View Full Document Right Arrow Icon

Info iconThis preview has intentionally blurred sections. Sign up to view the full version.

View Full DocumentRight Arrow Icon
This is the end of the preview. Sign up to access the rest of the document.

Unformatted text preview: Designation: A 813/A 813M 95 e 2 813M 01 An American National Standard Standard Specification for Single- or Double-Welded Austenitic Stainless Steel Pipe 1 This standard is issued under the fixed designation A 813/A 813M; the number immediately following the designation indicates the year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A superscript epsilon ( e ) indicates an editorial change since the last revision or reapproval. e 1 N OTE The Celsius conversion in 5.2.4 was added editorially in May 1996. e 2 N OTE The UNS designation N08367 was added to 5.2.1 in July 1996. 1. Scope 1.1 This specification covers two classes of fit-up and alignment quality straight-seam single- or double-welded austenitic steel pipe intended for high-temperature and general corrosive service. N OTE 1When the impact test criterion for a low-temperature service would be 15 ftlbf [20 J] energy absorption or 15 mils [0.38 mm] lateral expansion, some of the austenitic stainless steel grades covered by this specification are accepted by certain pressure vessel or piping codes without the necessity of making the actual test. For example, Grades 304, 304L, and 347 are accepted by the ASME Pressure Vessel Code, Section VIII Division 1, and by the Chemical Plant and Refinery Piping Code, ANSI B31.3 for service at temperatures as low as -425F [-250C] without qualification by impact tests. Other AISI stainless steel grades are usually accepted for service temperatures as low as -325F [-200C] without impact testing. Impact testing may, under certain circumstances, be required. For example, materials with chromium or nickel content outside the AISI ranges, and for material with carbon content exceeding 0.10 %, are required to be impact tested under the rules of ASME Section VIII Division 1 when service temperatures are lower than -50F [-45C] 1.2 Grades TP304H, TP304N, TP316H, TP316N, TP321H, TP347H, and TP348H are modifications of Grades TP304, TP316, TP321, TP347, and TP348, and are intended for high-temperature service. 1.3 Two classes of pipe are covered as follows: 1.3.1 Class SW Pipe, single-welded with no addition of filler metal and 1.3.2 Class DW Pipe, double-welded with no addition of filler metal. 1.4 Optional supplementary requirements are provided for pipe where a greater degree of testing is desired. These supplementary requirements call for additional tests to be made and, when desired, one or more of these may be specified in the order. 1.5 Table 1 lists the dimensions of welded stainless steel pipe as shown in ANSI B36.19. Pipe having other dimensions may be furnished provided such pipe complies with all other requirements of this specification....
View Full Document

This note was uploaded on 02/01/2012 for the course CIVL 2770 taught by Professor Fariborz during the Winter '11 term at Manitoba.

Page1 / 10

A 813 _ A 813M _ 95 ;QTGXMY9BODEZTS1SRUQ_ - Designation: A...

This preview shows document pages 1 - 2. Sign up to view the full document.

View Full Document Right Arrow Icon
Ask a homework question - tutors are online