A 134 _ 96 ;QTEZNC05NG__

A 134 _ 96 ;QTEZNC05NG__ - Designation: A 134 – 96 An...

Info iconThis preview shows pages 1–2. Sign up to view the full content.

View Full Document Right Arrow Icon

Info iconThis preview has intentionally blurred sections. Sign up to view the full version.

View Full DocumentRight Arrow Icon
This is the end of the preview. Sign up to access the rest of the document.

Unformatted text preview: Designation: A 134 – 96 An American National Standard Standard Specification for Pipe, Steel, Electric-Fusion (Arc)-Welded (Sizes NPS 16 and Over) 1 This standard is issued under the fixed designation A 134; the number immediately following the designation indicates the year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A superscript epsilon ( e ) indicates an editorial change since the last revision or reapproval. 1. Scope 1.1 This specification covers electric-fusion (arc)-welded straight seam or spiral seam steel pipe NPS 16 and over in diameter (inside or outside as specified by purchaser), with wall thicknesses up to 3 / 4 in. (19.0 mm), inclusive. Pipe having other dimensions may be furnished provided such pipe com- plies with all other requirements of this specification. N OTE 1—Acceptability for many services may be controlled by codes or standards such as those published by the American National Standards Institute and American Society of Mechanical Engineers. N OTE 2—For testing methods not specifically covered in this specifi- cation, reference can be made to Test Methods and Definitions A 370, with particular reference to Annex A 2 on Steel Tubular Products. N OTE 3—A comprehensive listing of standardized pipe dimensions is contained in ANSI B 36.10. 1.2 The values stated in inch-pound units are to be regarded as the standard. N OTE 4—The dimensionless designator NPS (nominal pipe size) has been substituted in this standard for such traditional terms as “nominal diameter”, “size”, and “nominal size”. 1.3 The following precautionary caveat pertains specifi- cally to Section 5 of this specification. This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 2. Referenced Documents 2.1 ASTM Standards: A 36/A 36M Specification for Carbon Structural Steel 2 A 283/A 283M Specification for Low and Intermediate Tensile Strength Carbon Steel Plates 2 A 285/A 285M Specification for Pressure Vessel Plates, Carbon Steel, Low- and Intermediate-Tensile Strength 2 A 370 Test Methods and Definitions for Mechanical Testing of Steel Products 3 A 570/A 570M Specification for Steel, Sheet and Strip, Carbon, Hot-Rolled, Structural Quality 4 2.2 ASME Boiler and Pressure Vessel Code: Section IX Welding Qualifications 5 2.3 American National Standards Institute Standard: B 16.25 Buttwelding Ends 6 B 36.10 Welded and Seamless Wrought Steel Pipe 6 3. Ordering Information 3.1 Orders for material under this specification should include the following, as required, to describe the desired material adequately: 3.1.1 Quantity (feet, meters, or number of lengths), 3.1.2 Name of material (electric-fusion-(arc) welded pipe), 3.1.3 Grade (Section 4),3....
View Full Document

This note was uploaded on 02/01/2012 for the course CIVL 2770 taught by Professor Fariborz during the Winter '11 term at Manitoba.

Page1 / 4

A 134 _ 96 ;QTEZNC05NG__ - Designation: A 134 – 96 An...

This preview shows document pages 1 - 2. Sign up to view the full document.

View Full Document Right Arrow Icon
Ask a homework question - tutors are online