Final Study Guide--Geology 1001 - Name scoreforthecourse..This

Final Study Guide--Geology 1001 - Name...

This preview shows page 1 out of 10 pages.

You've reached the end of your free preview.

Want to read all 10 pages?

Unformatted text preview: GEOL 1001 Physical Geology Name:______________________________________ Extra Credit Review Exercise. This exercise is a review for the final exam as well as a chance to earn 2 points of extra credit on your score for the course. Print out this document and fill in all of the answers in the spaces provided. This exercise is due at the final exam. It will not be accepted after the final exam. This exercise is intended to get you started in your studying these chapters. This is not intended to be an all‐inclusive review exercise and should not be interpreted that way. These are NOT all of the topics that might be covered on the final exam. Chapter 1‐ Introduction to earth science: Define Uniformitarianism: What are the major steps to the scientific method? Put the following in order from least dense to most dense: oceanic crust, continental crust, mantle rock, metallic iron. Chapter 2 – Plate tectonics: The three types of plate boundaries are: 1. 2. 3. A mid‐ocean ridge is a ________________________plate boundary. Oceanic crust that is close to a mid‐ocean ridge is (younger/older) than oceanic crust that is farther away from the mid‐ocean ridge. (circle one) Subduction occur when a. Two plates made of oceanic crust come together b. A plate made of oceanic crust meets a plate with continental crust c. Two plates made of continental crust come together d. Any of these is possible 1 Mantle convection works by (hot/cool) material rising, and (hot/cool) material sinking. (circle one) Hot material is (more/less) dense than cool material. Chapter 3 ‐ Minerals: Define a mineral: What are the different types of bonds that atoms can form with one another? The atomic number o f an atom refers to how many __________________ it contains. The basic building block of silicate minerals is the __________________________________. This building block is made of 1 __________ atom and 4 ___________ atoms. Define: Hardness – Cleavage – Luster – 2 Chapter 4 – Igneous rocks: (the following terms are to be used in the table below) A. Mafic a. Extrusive B. Intermediate b. Intrusive C. Felsic 1. Coarse grained I. Basalt 2. Fine grained II. Diorite III. Rhyolite IV. Gabbro V. Granite VI. Andesite Place one lower‐cased letter, one upper‐cased letter, one number, and one Roman numeral from the above lists in each of the six empty boxes. Igneous High Si Intermediate Si Low Si Rocks Low Mg + Fe Intermediate Mg + Fe High Mg + Fe Fast Cooling Slow Cooling All magmas that are generated in the mantle are _____________ in composition. Briefly describe these ways in which magmas can change their composition: Fractional Crystallization: Assimilation: Magma mixing: Chapter 7 Sedimentary Rocks: ____________ is the most common mineral in detrital sedimentary rocks. Define diagenesis. 3 The three types of sedimentary rocks are: a. Clastic, rhyolitic, and foliated b. Chemical, biological, and clastic c. Chemical, foliated, and clastic d. Biological, rounded, and mafic Fine grained sedimentary rocks are formed from deposits that are (near to/far from) the source rock. (circle one) Rounded sedimentary grains represent (short/far) transport distance. (circle one) List three typesof depositional environments for each of the following categories: Continental Shorline Marine Chapter 8 Metamorphic Rocks: Put these rocks in order from low grade to high grade: phyllite, schist, slate, gneiss Foliated rocks are associated with (regional/contact/shock) metamorphism. (circle one) Match the following metamorphic rocks with their parent rocks. Quartzite Shale Marble Sandstone Slate Limestone Gneiss What is an isograd? 4 List the three factors that can lead to metamorphism. Which metamorphic facies represents the highest temperature and pressure conditions? Chapter 9 Geologic Time: What is the difference between absolute age and relative age? Which principle involves the use of fossils as tools for correlating rock units? A fold where both limbs dip in the same direction is called ______________________________. If a sample has 25% of the parent isotope and 75% of the daughter isotope in an isotope system with a half‐life of 1 million years, then how old is the sample? 5 Place the following units and features in order from oldest (first to occur) to youngest. The wiggly line should be labeled D . Chapter 10 Deformation The figure represents a map view of rock units exposed at the Earth’s surface. This structure in the subsurface could be a syncline, an anticline or dipping unfolded units. Draw in strike and dip symbols that would be appropriate if this were an anticline. Also label the beds a, b, and c where a is the youngest unit and c is the oldest. 6 List the type of regional stresses and the resulting length change of the crust (ex. shortening, lengthening) for each type of fault listed below. • • • • Normal Reverse Strike‐slip Thrust The tendency of rock to behave in a brittle or ductile way depends on the ____________________. What type of faults occur at mid‐ocean ridges? Chapter 11 Earthquakes: An earthquake begins at one point within the crust which is called the _______________. The point on the surface of the earth that is directly above that is called the ____________________. Stress Time On the figure above label the level where the local rock strength can no longer handle the stress that is applied as “critical stress”. Label the places that indicate when earthquakes occur. How much stress is on the rock immediately after the earthquake has occurred? 7 Type of wave P – wave S – wave Surface wave Order of arrival at seismograph Type of displacement Material(s) they velocity can travel through Complete the table above. Seismograph readings can tell you a. b. c. d. How far away from an earthquake you are What type of motion occurred on the fault The Richter magnitude of the earthquake All of the above The largest earthquakes occur by movement along a plate boundary at a subduction zone. These are called __________________. Chapter 12 The Earth’s Interior: When an earthquake occurs, which direction(s) do seismic waves travel away from the focus? What is the difference between reflection and refraction? What property of rocks determines the velocity at which seismic waves travel through them? In two regions of the earth where the composition and mineralogy of the rocks are the same, seismic waves will travel faster through the region that is (warmer/colder). (circle one) 8 Chapter 16 Running Water What properties affect the velocity of a river? When does a river deposit sediment, and when does it erode? How is this related to base level? Describe the movement of water through the hydrologic cycle. Once precipitation has fallen on land, what paths might it take? Chapter 18 Glaciers List the major differences between mountain valley glaciers and continental glaciers. Describe the relationship between movement of a glacier, accumulation of ice, and wasting. 9 Which of the following are erosional features and which are depositional features: cirque, kames, morains, horns, eskers, arêtes, hanging valleys, drumlins, kettle lakes, tarns, glacial grooves. Erosional Depositional Chapter 21 Climate: What are the components of the climate system? What is the difference between a positive and negative feedback? List three different time scales on which temperatures on the earth change. How have humans influenced the climate in the past century? 10 ...
View Full Document

  • Spring '07
  • BAKSI
  • Geology, Detrital sedimentary, Luster, a. Extrusive, c. Felsic, A. Clastic, A. Mafic

  • Left Quote Icon

    Student Picture

  • Left Quote Icon

    Student Picture

  • Left Quote Icon

    Student Picture