Lab 5 Configuring Basic RIPv2.docx - ET0010 ET0882 Computer...

This preview shows page 1 - 4 out of 7 pages.

ET0010/ ET0882 Computer Networking Lab – Configuring Basic RIPv2 Topology Addressing Table Device Interface IP Address Subnet Mask Default Gateway R1 G0/1 172.30.10.1 255.255.255.0 N/A S0/0/0 (DCE) 10.1.1.1 255.255.255.252 N/A R2 G0/0 209.165.201.1 255.255.255.0 N/A S0/0/0 10.1.1.2 255.255.255.252 N/A S0/0/1 (DCE) 10.2.2.2 255.255.255.252 N/A R3 G0/1 172.30.30.1 255.255.255.0 N/A S0/0/1 10.2.2.1 255.255.255.252 N/A © 2020 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 1 of 7
Lab – Configuring Basic RIPv2 S1 N/A VLAN 1 N/A N/A S3 N/A VLAN 1 N/A N/A PC-A NIC 172.30.10.3 255.255.255.0 172.30.10.1 PC-B NIC 209.165.201.2 255.255.255.0 209.165.201.1 PC-C NIC 172.30.30.3 255.255.255.0 172.30.30.1 Objectives Part 1: Build the Network and Configure Basic Device Settings Part 2: Configure and Verify RIPv2 Routing Configure RIPv2 on the routers and verify that it is running. Configure a passive interface. Examine routing tables. Disable automatic summarization. Configure a default route. Verify end-to-end connectivity. Background / Scenario RIP version 2 (RIPv2) is used for routing of IPv4 addresses in small networks. RIPv2 is a classless, distancevector routing protocol, as defined by RFC 1723. Because RIPv2 is a classless routing protocol, subnet masks are included in the routing updates. By default, RIPv2 automatically summarizes networks at major network boundaries. When automatic summarization has been disabled, RIPv2 no longer summarizes networks to their classful address at boundary routers. In this lab, you will configure the network topology with RIPv2 routing, disable automatic summarization, propagate a default route, and use CLI commands to display and verify RIP routing information. In Packet Tracer environment, use Cisco 1941 for the router and Cisco 2960 for the switches. Part 1: Build the Network and Configure Basic Device Settings In Part 1, you will set up the network topology and configure basic settings. Step 1: Cable the network as shown in the topology. Step 2: Initialize and reload the router and switch. Step 3: Configure basic settings for each router and switch. a. Disable DNS lookup. (no ip domain-lookup) b. Configure device names as shown in the topology. c. Configure password encryption. d. Assign class as the privileged EXEC password. e. Assign cisco as the console and vty passwords. f. Configure a MOTD banner to warn users that unauthorized access is prohibited. g. Configure logging synchronous for the console line. h. Configure the IP addresses listed in the Addressing Table for all interfaces. i. Configure a description for each interface with an IP address. © 2020 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 2 of 7
Lab – Configuring Basic RIPv2 j. Configure the clock rate, if applicable, to the DCE serial interface. k. Copy the running-configuration to the startup-configuration. Step 4: Configure PC IP Addressing. Refer to the Addressing Table for IP address information of the PCs.

  • Left Quote Icon

    Student Picture

  • Left Quote Icon

    Student Picture

  • Left Quote Icon

    Student Picture