11 215 25 325 70 8 28 34 3 55 65 95 84 34 50 7 55 19

Info iconThis preview shows page 1. Sign up to view the full content.

View Full Document Right Arrow Icon
This is the end of the preview. Sign up to access the rest of the document.

Unformatted text preview: 800 25 I 780 90 99 165 20 67 78 8 15 15 210 221 103 100 I5 12 78 2’5 2’5 12 2 000 25 1 935 100 109 165 20 67 78 8 I5 I5 215 242 II3 100 I5 I2 88 2.5 2‘5 12 2 2GO 25 2 130 110 119 165 20 67 78 8 15 IS 220 264 123 100 15 I2 98 2‘5 2’5 12 these are critical NOTE 1 -Corners Non 2 -The guidance only. to be rounded off. dimensions TS. T, Ii. S, HT and Kshall conform to the ~&es The following tolerances shall apply on the critical dimensions: given in this table as Dimensions Other dimensions TOlt?MlW~S TandKT Same as that TS and H Half the tolerance K and S of wall thickness f0.25 given in 7.2. on wall thickness mm for dimensions &@5 mm for dimensions .. dimensions. given in 7.2. up to and including above IO mm, I 41. 10 mm, and are for TABLE IO SPIGOT AND SOCKET DIMENSIONS OF NP3 AND NP4 CLASS PIPES FROM 80 TO 900 mm DIAMETER f Clauses All dimensions TS RING ROLL~ON JOINT ) 5.3 and 1.2 ) in millimctres. LIEFFECTIVE T ( RUBBER DS DSI DSZ DA-3 R LSD LENGTH) K N HT CT LSP P S H X (18) (19) W R, (1) (3) (4) (5) (6) (7) (8) (9) (IO) (11) (12) (13) (14) (15) (16) (17) (20) (21) (22) II 102 25 32’5 70 8 28 34 3 5’5 6’5 95 84 34 50 7 5’5 19’5 1 1 5’5 100 II 120 25 32’5 70 8 28 34 3 5’5 6’5 95 84 34 50 7 5.5 195 1 I 5’5 150 II 170 25 32’5 70 8 28 34 3 5’5 6’5 95 84 34 50 7 5’5 19’5 I I 5’5 200 11 230 30 38 81 11 38 34 5 6’5 6’5 113 97 395 50 7 5’5 24’5 1 I 5’5 125 II 255 30 38 83 II 38 34 5 6’S 6’5 113 91 39’5 50 7 5’5 24’5 t 1 5’5 250 11 275 30 38 83 II 38 34 5 6’5 6’5 113 97 39’5 50 7 5’5 24’5 I 1 5‘5 300 12 340 40 51 90 12 42 36 6 7 I 130 130 53 55 7’5 6 34 1 I 6 350 16 435 73 75 120 16 56 48 8 10 10 158 135 78 72 103 67 2 28 400 z (2) 80 16 480 75 7s 120 16 56 48 8 10 10 158 135 78 72 108 67 2 2 it 450 16 525 75 75 120 16 56 48 8 10 10 I58 135 78 72 108 67 2 2 8 500 16 570 75 75 150 16 56 48 8 10 10 158 135 78 12 IO 8 67 2 2 8 600 20 675 85 85 150 20 70 60 IO 12 12 193 153 88’5 PO 12 10 75 2 2 10 700 20 765 as 85 150 20 70 60 10 I2 12 193 153 88’5 90 12 10 75 2 2 10 800 20 875 95 95 150 20 70 60 10 12 12 197 171 98.5 PO 12 10 85 2 2 10 900 20 970 100 100 150 20 70 6Q 10 12 12 200 180 103’5 90 12 10 90 2 2 10 *on 1 -Corners NOTE 2 guidance to be rounded The dimensions only. rS. ‘Fix fOllOWin OR. T, I?. S. HT and K shall tolerances shall apply conform on the critical to the. values given in this table as these are critical Other dimensions. dimensions dimensions: Dimensions TOh~M?~ T and HT same TS and If Half the tolerance KandS f025 as that of wall thickness given on wall thickness mm for dimensions & @5 mm for dimensions in 7.2. liven in 7.2. up to and including above 10 mm. 10 mm. and are for -- TMLE II SPIGOT AND SOCKET DIMENSIONS ---- .--^ OF NP3 AND NP4 CLASS PIPES FROM 1000 ( Clauses All dimensions RUBBER TO 2 600 mm DIAMETER ( RUBBER RING CONFINED JbINT 5.3 and 7.2 ) in mlllimetrsr. RING\ T TS LS LSI K LSP (I b J H i DIAM!?TER D L (1) (2) (3) (4) (5) C-5) (7) (‘3) (9) (W (10 W2) (13) (14) 1 000 20 920 115 58 114 20 13 114 25 28 39 42 4 (15) (1.5) I 102 9 I 202 1 307 1 100 20 1 003 II5 58 114 20 13 114 25 28 39 41 4 9 1 200 20 1 095 120 60’5 114...
View Full Document

This document was uploaded on 10/01/2013.

Ask a homework question - tutors are online