168101 will be the source address used for Cisco Phones Primary CME router will

168101 will be the source address used for cisco

This preview shows page 170 - 175 out of 526 pages.

The HSRP IP of 192.168.10.1 will be the source address used for Cisco Phones Primary CME router will be CME1. The Secondary will be CME2 >>CME1<< interface fastethernet0/1 ip address 192.168.10.2 255.255.255.0 standby ip 192.168.10.1 standby priority 150 standby preempt telephony-service ip source-address 192.168.10.1 port 2000 >>CME2<< interface fastethernet0/1 ip address 192.168.10.3 255.255.255.0 standby ip 192.168.10.1 standby priority 100 telephony-service ip source-address 192.168.10.1 port 2000 Configuration Reference Guide | [C] 170
Image of page 170
IP Phone Redundancy using Secondary CME Configure CME redundancy using the Secondary command Primary CME router will be CME1 (192.168.10.1) and the Secondary will be CME2 (192.168.10.2) telephony-service ip source-address 192.168.10.1 port 2000 secondary 192.168.10.2 Configuration Reference Guide | [C] 171
Image of page 171
Redundant CME using Gatekeepers CME1 and CME2 pointing to H.323 Gatekeeper Router (192.168.11.1) >>CME1<< interface FastEthernet0/1 ip address 192.168.10.1 255.255.255.0 h323-gateway voip interface h323-gateway voip id siteA ipaddr 192.168.11.1 1719 h323-gateway voip h323-id CME1 h323-gateway voip tech-prefix 1# h323-gateway voip bind srcaddr 192.168.10.1 >>CME2<< interface FastEthernet0/1 ip address 192.168.10.2 255.255.255.0 h323-gateway voip interface h323-gateway voip id siteA ipaddr 192.168.11.1 1719 h323-gateway voip h323-id CME2 h323-gateway voip tech-prefix 1# h323-gateway voip bind srcaddr 192.168.10.2 Configuration Reference Guide | [C] 172
Image of page 172
Define the local zone for the site with the CME routers as “TRA” Specify primary call routing to IP Phones using 6XXX extensions through CME1 (access code is 8) Specify secondary call routing to IP Phones using 6XXX extensions through CME2 (access code is 8) >>GK<< gatekeeper zone local TRA routehub.local 192.168.11.1 zone prefix TRA 86... gw-priority 10 CME1 zone prefix TRA 86... gw-priority 9 CME2 zone gw-type prefix 1# default-technology VoiceView Enable VoiceView on CUE service voiceview enable session idletimeout 30 end Add URL for VoiceView authentication on CME router Enable VoiceView URL on CME to be accessed under Phone Services telephony-service url authentication MWI on Second Line Enable MWI red-light notification if a new voicemail comes in for the extension on line 2 (using ephone-dn 15) ephone 10 1:14 2:15 mwi-line 2 Configuration Reference Guide | [C] 173
Image of page 173
IP Phone Backlight Display Keeps the backlight turned on instead of turning off on the Cisco Phone display Router(config)# telephony-service Router(config-telephony)# service phone displayOnWhenIncomingCall 1 SIP: Call Forward Default behavior for Cisco CME is to send a "302 Moved Temporarily" SIP message to the SIP proxy. The following configuration is how you can disable this if the SIP provider doesn’t support this for call forwarding busy (CFB) flows. voice service voip no supplementary-service sip moved-temporarily SIP: Call Transfer CME by default will send a SIP REFER message to the SIP server. Most Service SIP Provider don't support the REFER method, therefore, it must be forced on the CME to hairpin the call.
Image of page 174
Image of page 175

  • Left Quote Icon

    Student Picture

  • Left Quote Icon

    Student Picture

  • Left Quote Icon

    Student Picture