SST 0963110021 0992210010 Torque 50 Nm 513 kgfcm 37 ftlbf NOTICEUse SST

Sst 0963110021 0992210010 torque 50 nm 513 kgfcm 37

This preview shows page 45 - 48 out of 48 pages.

SST 09631–10021, 09922–10010 Torque: 50 N·m (513 kgf·cm, 37 ft·lbf) NOTICE: Use SST 09922–10010 in the direction shown in the illustra- tion. HINT: Use a torque wrench with a fulcrum length of 345 mm (13.58 in.). (c) Recheck the total preload. Preload (turning): 0.8 – 1.4 N·m (8 – 14 kgf·cm, 6.9 – 12.2 in.·lbf) (d) Remove the RH and LH rack ends. 17. INSTALL RH AND LH CLAW WASHERS AND RACK ENDS (a) Install a new claw washer, and temporarily install the rack end. HINT: Align the claws of the washer with the steering rack grooves. (b) Using a spanner (24 mm) to hold the steering rack steady, and using SST, torque the rack end. SST 09922–10010 Torque: 60 N·m (615 kgf·cm, 45 ft·lbf) NOTICE: Use SST 09922–10010 in the direction shown in the illustra- tion. HINT: Use a torque wrench with a fulcrum length of 345 mm (13.58 in.). (c) Using a brass bar and hammer, stake the washer. NOTICE: Avoid any impact to the rack.
Image of page 45
R11669 W04223 SST 2 mm (0.79 in.) or less W04231 Fulcrum SST Length SR–46 STEERING POWER STEERING GEAR 1342 AuthorĂ: DateĂ: 1997 LEXUS ES300 (RM511U) 18. INSTALL RH AND LH RACK BOOTS, CLAMPS AND CLIPS (a) Ensure that the steering rack hole is not clogged with grease. HINT: If the hole is clogged, the pressure inside the boot will change after it is assembled and the steering wheel is turned. (b) Install the boot. NOTICE: Be careful not to damage or twist the boot. (c) Using SST, tighten the clamp as shown in the illustration. SST 09521–24010 19. INSTALL RH AND LH TIE ROD ENDS AND LOCK NUTS (a) Screw the lock nut and tie rod end onto the rack end until the matchmarks are aligned. (b) After adjusting toe–in, torque the nut. (See page SA–4 ) Torque: 74 N·m (750 kgf·cm, 54 ft·lbf) 20. INSTALL 2 TURN PRESSURE TUBES (a) Coat 2 new O–rings with power steering fluid and install them to the tube. (b) Using SST, install the tube. SST 09633–00020 Torque: 10 N·m (102 kgf·cm, 7 ft·lbf) HINT: L Use a torque wrench with a fulcrum length of 250 mm (9.84 in.). L This torque value is effective in case that SST is parallel to a torque wrench.
Image of page 46
SR069–01 W04224 SST Length Fulcrum STEERING POWER STEERING GEAR SR–47 1343 AuthorĂ: DateĂ: 1997 LEXUS ES300 (RM511U) INSTALLATION 1. INSTALL PS GEAR ASSEMBLY (a) Install the gear assembly from the LH of the vehicle. NOTICE: Do not damage the turn pressure tubes. (b) Torque the 2 gear assembly set bolts and nuts. Torque: 181 N·m (1,850 kgf·cm, 134 ft·lbf) HINT: Lift up the stabilizer bar and install the bolts. 2. INSTALL NO.1 FUEL TUBE PROTECTOR Install the 2 bolts and nut. 3. CONNECT STABILIZER BAR Torque the 4 bolts. Torque: 19 N·m (195 kgf·cm, 14 ft·lbf) 4. CONNECT PRESSURE FEED AND RETURN TUBES Using SST, connect the tube. SST 09631–22020 Torque: 32 N·m (326 kgf·cm, 24 ft·lbf) HINT: L Use a torque wrench with a fulcrum length of 300 mm (11.81 in.). L This torque value is effective in case that SST is parallel to a torque wrench. 5. CONNECT CLAMP PLATE Torque the nut. Torque: 10 N·m (100 kgf·cm, 7 ft·lbf) 6. CONNECT INTERMEDIATE SHAFT ASSEMBLY (See page SR–16 ) 7. CONNECT RH AND LH TIE ROD ENDS (See page SA–9 ) 8. POSITION FRONT WHEELS FACING STRAIGHT AHEAD HINT: Do it with the front of the vehicle jacked up.
Image of page 47
Image of page 48

  • Left Quote Icon

    Student Picture

  • Left Quote Icon

    Student Picture

  • Left Quote Icon

    Student Picture