Course Hero Logo

Described in table 105 figure 74 apbhm to ugps cable

Course Hero uses AI to attempt to automatically extract content from documents to surface to you and others so you can study better, e.g., in search results, to enrich docs, and more. This preview shows page 217 - 221 out of 300 pages.

described inTable 105.Figure 74 AP/BHM to UGPS cableNoteThis is only applicable for 450 AP/BHM.The AP/BHM will only power up the UGPS if it configured to do so.``RJ45 Connector (Bottom)Straight-Through CableRJ12 Connector (Top)6NC543NC2187654321
Chapter 4: Preparing for installationODU interfacesPage4-16Table 105 AP/BHM to UGPS cable pinoutPin450i Series AP RJ 45ConnectorPinUGPS RJ 12 ConnectorConnector1NC18 on RJ 452NC2NC3NC35 on RJ 4544 on RJ 1244 on RJ 4553 on RJ 125NC6NC67 on RJ 4576 on RJ 1281 on RJ 12Alignment tone cable (for PMP/PTP 450i)The alignment tone cable is constructed using RJ45 plug and Stereo plug. The pin configuration isshown in Figure 75Figure 75 Alignment tone cable pin configurationFor more information, referAux port to alignment tone headset wiring.Override plug cable (for PMP 450 only)To construct an override plug, perform the following steps:Crimp an RJ-12 6 pins connector onto a 6-inch length of CAT 5 cablePin out all 6 pinsShort (solder together) pins 4 and 6 on the other end. Do not connect any other wires to anything.220 Ω220 ΩResistorsPin 7Pin 4LeftRightCommon#8#1
Chapter 4: Preparing for installationODU interfacesPage4-17Figure 76 RJ-12 pinout for the default plug``RJ12 Connector (Bottom)Override plug cable wiring654321Tie togetherNot usedNot usedNot used
Chapter 4: Preparing for installationODU interfacesPage4-18Configuring Link for TestIt is important to stage the AP/BHM and SM/BHS units first to verify proper registration beforedeploying the modules to the site. To begin configuring the modules for test, see the sections below:Configuring the management PCTo configure the local management PC to communicate with the AP, SM, BHM or BHS, proceed asfollows:Powering the AP/SM/BH for test configurationPerform the following steps to power on the ODU.Procedure 2 Powering the ODU1Plug one end of a CAT 5 Ethernet cable into the ODU.2Plug the Ethernet cable connector labeled To Radio into the jack in the pig tail thathangs from the power supply.3Plug the other connector of the pig tail (this connector labeled To Computer) intothe Ethernet jack of the computing device.4Plug the power supply into an electrical outlet.WarningFrom this point until you remove power from the ODU, stay at least as farfrom the AP as the minimum separation distance specified inError!Reference source not found.on pageError! Bookmark not defined..5Power up the computing device6Start the browser in the computing deviceThe AP/BHM interface provides a series of web pages to configure and monitor the unit. Access web-based interface through a computing device that is either directly connected or connected through anetwork to the AP/BHM. If the computing device is not connected to a network when it is beingconfigured for test environment, and if the computer has used a proxy server address and port toconfigure a module, then the operator may need to first disable the proxy setting in the computer.

Upload your study docs or become a

Course Hero member to access this document

Upload your study docs or become a

Course Hero member to access this document

End of preview. Want to read all 300 pages?

Upload your study docs or become a

Course Hero member to access this document

Term
Spring
Professor
N/A
Tags
ODU, Yagi antenna, Directional antenna

Newly uploaded documents

Show More

Newly uploaded documents

Show More

  • Left Quote Icon

    Student Picture

  • Left Quote Icon

    Student Picture

  • Left Quote Icon

    Student Picture