Information necessary to service the system safely is included in the SRS and

Information necessary to service the system safely is

This preview shows page 3 - 6 out of 32 pages.

air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted. Information necessary to service the system safely is included in the SRS and SB section of this Service Man- ual. WARNING: To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in the event of a collision which would result in air bag inflation, all maintenance must be per- formed by an authorized NISSAN/INFINITI dealer. Improper maintenance, including incorrect removal and installation of the SRS, can lead to per- sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag Module, see the SRS section. Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness connectors. Precautions for Brake System EFS0037W Refer to MA-11, " RECOMMENDED FLUIDS AND LUBRICANTS " for recommended brake fluid. Do not reuse drained brake fluid. Be careful not to splash brake fluid on painted areas. To clean or wash all parts of master cylinder, disc brake caliper and wheel cylinder, use clean brake fluid. Do not use mineral oils such as gasoline or kerosene. They will ruin rubber parts of the hydraulic system. Use flare nut wrench when removing and installing brake tube. Always check tightening torque when installing brake lines. Before working, turn ignition switch to OFF and disconnect con- nectors for ABS actuator and electric unit (control unit) or battery terminals. Burnish the brake contact surfaces after refinishing or replacing drums or rotors, after replacing pads or linings, or if a soft pedal occurs at very low mileage. Refer to BR-24, " BRAKE BURNISH- ING PROCEDURE " . WARNING: Clean brake pads and shoes with a waste cloth, then wipe with a dust collector. SBR686C
Image of page 3
BR-4 PREPARATION Revision: January 2005 2004 Pathfinder Armada PREPARATION PFP:00002 Special Service Tool EFS005TW The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here. Commercial Service Tools EFS005TX Tool number (Kent-Moore No.) Tool name Description (J-46532) Brake and clutch pedal height measure- ment tool Measuring brake pedal height LFIA0227E Tool name Description 1. Flare nut crowfoot 2. Torque wrench Removing and installing each brake pip- ing. a: 10 mm (0.39 in) / 12 mm (0.47 in) Power tool Removing nuts, bolts and screws. S-NT360 PBIC0190E PBIC0191E
Image of page 4
NOISE, VIBRATION, AND HARSHNESS (NVH) TROUBLESHOOTING BR-5 C D E G H I J K L M A B BR Revision: January 2005 2004 Pathfinder Armada NOISE, VIBRATION, AND HARSHNESS (NVH) TROUBLESHOOTING PFP:00003 NVH Troubleshooting Chart EFS0037Y Use the chart below to help you find the cause of the symptom. If necessary, repair or replace these parts. × : Applicable Reference page BR-20 , BR-25 BR-20 , BR-25 BR-20 , BR-25 BR-24 , BR-28 BR-24 , BR-28 BR-24 , BR-28 BR-24 , BR-28 BR-24 , BR-28 BR-24 , BR-29 BR-24 , BR-29 PR-3, " NVH Troubleshooting Chart " RFD-5, " NVH Troubleshooting Chart " PR-3, " NVH Troubleshooting Chart " FSU-4, " NVH Troubleshooting Chart " (FSU), RSU-5, " NVH Troubleshooting Chart " (RSU) WT-3, "
Image of page 5
Image of page 6

  • Left Quote Icon

    Student Picture

  • Left Quote Icon

    Student Picture

  • Left Quote Icon

    Student Picture