Bolt length Bolt A 22 mm 0866 in Bolt B 37 mm 1457 in a Align the manual valve

Bolt length bolt a 22 mm 0866 in bolt b 37 mm 1457 in

This preview shows page 136 - 139 out of 139 pages.

Bolt length: Bolt A: 22 mm (0.866 in.) Bolt B: 37 mm (1.457 in.) (a) Align the manual valve with the pin on the manual shaft lever. (b) Lower the manual valve body into place. (c) Hand tighten the 5 bolts first. Then, tighten them with a torque wrench. Torque: 11 N·m (110 kgf·cm, 8 ft·lbf) (d) Place the detent springs on the manual valve body and hand tighten the 2 bolts first. Then, tighten them with a torque wrench. Torque: 11 N·m (110 kgf·cm, 8 ft·lbf) HINT: Each bolt length is indicated below. Bolt length: Bolt A: 14 mm (0.551 in.) Bolt B: 37 mm (1.457 in.) (e) Check that the manual valve lever is touching the center of the detent spring tip roller. 11. INSTALL PIPE BRACKET AND OIL STRAINER Each bolt length is indicated below. Bolt length: Bolt A: 22 mm (0.866 in.) Bolt B: 53 mm (2.087 in.) Torque: Pipe bracket: 10 N·m (100 kgf·cm, 7 ft·lbf) Oil strainer: 11 N·m (110 kgf·cm, 8 ft·lbf)
Image of page 136
AUTOMATIC TRANSAXLE COMPONENT PARTS INSTALLATION - AX-1 19 12. INSTALL MAGNETS IN PLACE NOTICE: Make sure that the magnets do not interfere with the oil pipes. 13. INSTALL OIL PAN WITH NEW GASKET (a) Install a new gasket and oil pan. (b) Install and torque the 17 bolts. Torque: 4.9 N·m (50 kgf·cm, 43 in.·lbf) 14. INSTALL THROTTLE CABLE RETAINING PLATE 15. INSTALL TRANSAXLE UPPER COVER 16. INSTALL T/M REVOLUTION SENSOR (a) Install a new O-ring to the T/M revolution sensor. (b) Install the T/M revolution sensor with the bolt.
Image of page 137
AUTOMATIC TRANSAXLE COMPONENT PARTS INSTALLATION - AX-120 17. INSTALL PARK/NEUTRAL POSITION SWITCH (a) Install the park/neutral position switch to the manual valve shaft. (b) Place the new locking plate and tighten the nut. (c) Stake the nut with locking plate. (d) Install the 2 bolts. (e) Adjust the park/neutral position switch. HINT: Align the groove and neutral basic line. (f) Tighten the 2 bolts. 18. INSTALL UNION AND ELBOW (a) Install the new O-rings to the union and elbow. (b) Install the union elbow to the transaxle case. Torque: 27 N·m (275 kgf·cm, 20 ft·lbf) HINT: Install the elbow, as shown in the illustration. 19. INSTALL MANUAL SHAFT LEVER
Image of page 138
AUTOMATIC TRANSAXLE COMPONENT PARTS INSTALLATION - AX-121 20. INSTALL SHIFT CONTROL CABLE BRACKET
Image of page 139

You've reached the end of your free preview.

Want to read all 139 pages?

  • Spring '14
  • pistons, SST, Automatic transmission, Gear ratio, Fuel injection, AUTOMATIC TRANSAXLE

  • Left Quote Icon

    Student Picture

  • Left Quote Icon

    Student Picture

  • Left Quote Icon

    Student Picture

Stuck? We have tutors online 24/7 who can help you get unstuck.
A+ icon
Ask Expert Tutors You can ask You can ask You can ask (will expire )
Answers in as fast as 15 minutes