SF05S03 S04591 S04590 SF14 SFI FUEL PRESSURE REGULATOR 865 Author\u0102 Date\u0102 1997

Sf05s03 s04591 s04590 sf14 sfi fuel pressure

This preview shows page 14 - 19 out of 66 pages.

SF05S–03 S04591 S04590 SF–14 SFI FUEL PRESSURE REGULATOR 865 AuthorĂ: DateĂ: 1997 LEXUS ES300 (RM511U) REMOVAL 1. REMOVE FUEL PUMP ASSEMBLY FROM FUEL TANK (See page SF–10 ) 2. REMOVE FUEL FILTER (a) Remove the screw, and pull out the fuel filter. (b) Remove the O–ring from the fuel filter. HINT: At the time of installation, please refer to the following item. Apply a light coat of gasoline to a new O–ring, and install it to the fuel filter. Torque: 2.0 N·m (20 kgf·cm, 17 in.·lbf) 3. REMOVE FUEL PRESSURE REGULATOR (a) Remove the screw, and pull out the pressure regulator. Torque: 2.0 N·m (20 kgf·cm, 17 in.·lbf) (b) Remove the O–ring from the pressure regulator. HINT: At the time of installation, please refer to the following item. Apply a light coat of gasoline to a new O–ring, and install it to the pressure regulator.
Image of page 14
SF05T–01 SFI FUEL PRESSURE REGULATOR SF–15 866 AuthorĂ: DateĂ: 1997 LEXUS ES300 (RM511U) INSTALLATION Installation is in the reverse order of removal (See page SF–14 ).
Image of page 15
S05625 5 mm Hexagon Wrench Clip SF072–06 S04535 Sound Scope S04534 Ohmmeter SF–16 SFI INJECTOR 867 AuthorĂ: DateĂ: 1997 LEXUS ES300 (RM511U) INJECTOR ON–VEHICLE INSPECTION 1. REMOVE V–BANK COVER (a) Using a 5 mm hexagon wrench, remove the 2 cap nuts. (b) Disconnect the 2 clips, and remove the V–bank cover. 2. INSPECT INJECTOR OPERATION Check operation sound from each injector. (1) With the engine running or cranking, use a sound scope to check that there is normal operating noise in proportion to engine speed. (2) If you have no sound scope, you can check the in- jector operating vibration with your finger. If no sound or unusual sound is heard, check the wiring connec- tor, injector or injection signal from the ECM. 3. INSPECT INJECTOR RESISTANCE (a) Disconnect the injector connector. (b) Using an ohmmeter, measure the resistance between the terminals. Resistance: 13.8 at 20 ° C (68 ° F) If the resistance is not as specified, replace the injector. (c) Reconnect the injector connector. 4. REINSTALL V–BANK COVER HINT: For fixing the V–bank cover, push on the cover until a ”click” is felt.
Image of page 16
SF073–05 S05371 PS Pressure Tube Air Intake Chamber Stay 19.5 (200, 14) 39 (400, 19) 12 (120, 9) V–Bank Cover z Gasket No.2 EGR Pipe Throttle Position Sensor Connector z Gasket Brake Booster Vacuum Hose EGR Valve Position Sensor Connector Accelerator Cable Throttle Cable Air Cleaner Hose IAC Valve Connector EGR Gas Temperature Sensor Connector EVAP Hose Water Bypass Hose Vacuum Hose z Gasket VSV Connector for ASIC No.1 Engine Hanger Ground Cable Ground Cable Ground Strap DLC1 PCV Hose Air Intake Chamber Assembly Water Bypass Hose Air Assist Hose and Pipe 19.5 (200, 14) z Retainer Injector Connector Delivery Pipe 10 (100, 7) Spacer z O–Ring z Grommet z Grommet z O–Ring N·m (kgf·cm, ft·lbf) : Specified z Non–reusable part 43 (440, 32) VSV Connector for EGR Engine Wire VSV Connector for EVAP Injector High–Tension Cord Set SFI INJECTOR SF–17 868 AuthorĂ: DateĂ: 1997 LEXUS ES300 (RM511U) COMPONENTS
Image of page 17
S04505 SF074–04 S04498 S06086 Fuel Hose Clamp S05352 S04499 SF–18 SFI INJECTOR 869 AuthorĂ: DateĂ: 1997 LEXUS ES300 (RM511U) REMOVAL 1. REMOVE AIR CLEANER HOSE 2. REMOVE AIR INTAKE CHAMBER ASSEMBLY (See page EM–30 ) 3. DISCONNECT INJECTOR CONNECTORS 4.
Image of page 18
Image of page 19

You've reached the end of your free preview.

Want to read all 66 pages?

  • Spring '14
  • Lexus, Fuel injection, SFI, LEXUS ES300, Throttle position sensor

  • Left Quote Icon

    Student Picture

  • Left Quote Icon

    Student Picture

  • Left Quote Icon

    Student Picture