b Remove the 2 gaskets and plate c Remove the 3 check balls from the cover 11

B remove the 2 gaskets and plate c remove the 3 check

This preview shows page 95 - 100 out of 139 pages.

(b) Remove the 2 gaskets and plate. (c) Remove the 3 check balls from the cover. 11. REMOVE BOLTS FROM UPPER VALVE BODY Remove the 3 bolts. 12. LIFT OFF UPPER VALVE BODY AND NO.1 PLATE AS A SINGLE UNIT Hold No.1 plate to the upper valve body and lift off the up- per valve body. HINT: Be careful that the check balls and oil strainer do not fall out.
Image of page 95
AUTOMATIC TRANSAXLE VALVE BODY - AX-78 13. REMOVE 2 CHECK BALLS AND VIBRATING STOP- PER FROM UPPER VALVE BODY 14. REMOVE 2 OIL STRAINERS AND CHECK BALL FROM LOWER VALVE BODY VALVE BODY ASSEMBLY 1. INSTALL 2 CHECK BALLS AND VIBRATING STOP- PER TO UPPER VALVE BODY 2. INSTALL 2 OIL STRAINERS AND CHECK BALL TO LOWER VALVE BODY 3. POSITION PLATE AND NEW GASKETS ON UPPER VALVE BODY Position new No.1 gasket, plate and the new No.2 gasket on the upper valve body. HINT: Since No.1 gasket and No.2 gasket are similar, use the illustration below to discriminate between them. AX0TX-01
Image of page 96
AUTOMATIC TRANSAXLE VALVE BODY - AX-79 4. PLACE UPPER VALVE BODY WITH PLATE AND GAS- KETS ON LOWER VALVE BODY Hold the upper valve body, plate and gaskets securely so they do not separate. Align each bolt hole in the valve bodies with the gaskets and plate. 5. INSTALL AND FINGER TIGHTEN BOLTS IN UPPER VALVE BODY TO SECURE LOWER VALVE BODY Install and finger tighten the 3 bolts. HINT: Each bolt length is indicated below. Bolt length: Bolt A: 44 mm (1.732 in.) Bolt B: 16 mm (0.630 in.) 6. INSTALL NO.2 LOWER VALVE BODY COVER GAS- KETS, PLATE AND 3 CHECK BALLS (a) Install the 3 check balls into the No.2 lower valve body cover.
Image of page 97
AUTOMATIC TRANSAXLE VALVE BODY - AX-80 (b) Position a new gasket and plate and then another new gasket. HINT: Both gaskets are identical. (c) Install the 2 screws. 8. INSTALL NO.2 LOWER VALVE BODY COVER (a) Position the No.2 lower valve body cover. (b) Install and finger tighten the 11 bolts. HINT: Each bolt length is indicated below. Bolt length: Bolt A: 40 mm (1.575 in.) Bolt B: 44 mm (1.732 in.) Bolt C: 14 mm (0.551in.) 9. INSTALL OIL STRAINER AND CHECK VALVE Install the oil strainer and check valve into the lower valve body.
Image of page 98
AUTOMATIC TRANSAXLE VALVE BODY - AX-81 10. INSTALL LOWER VALVE BODY COVER GASKETS AND NO.2 PLATE Position a new gasket and plate and then another new gasket. HINT: Both gaskets are identical. 11. INSTALL LOWER VALVE BODY COVER (a) Position the lower valve body cover. (b) Install and finger tighten the 5 bolts. HINT: Each bolt length is indicated below. Bolt length Bolt A: 47 mm (1.850 in.) Bolt B: 14 mm (0.551 in.) 12. INSTALL PRESSURE RELIEF VALVE
Image of page 99
Image of page 100

  • Left Quote Icon

    Student Picture

  • Left Quote Icon

    Student Picture

  • Left Quote Icon

    Student Picture