1 2 19 thickness clearance 20 radius stretch 21

This preview shows page 12 - 15 out of 18 pages.

1219. thickness / clearance20. radius / stretch21. protractor22. hardware / fractional / metric23. two24. head / slipping25. pull / push / slipping
Answers 14126. box-end27. box-end / six28. box-end / open-end29. slippage30. inner / fixed31. 0.028 /3432. drive33. fractional-sized34. ratchet handle35. deep / six / twelve36. pointer / scale37. dial gage38. micrometer39. calibrated40. sharp / pipes / rods41. spanner / notches42. hook / periphery43. recessed / face44. width / diameter45. Phillips / positive46. offset47. gripping / cutting / slip48. channel-lock / curved49. cam / lever50. diagonal / cotter / pins51. needle-nose / long-nose52. duck-bill / flat / gripping53. shape / peen54. cut / harder55. chisel / hardened56. cutting / sheet / bar57. 10 / 3258. forward / forward59. relative position60. lower61. hardened / chisel62. tang / handle63. face / back64. double-cut / overcut / upcut65. teeth / soft66. rough / bastard / smooth67. shape / tapered / blunt68. rectangular / slightly tapered69. tapered / blunt / single70. three-square / tapered71. drawfiling72. spiral / twist73. shank / tapered74. flutes / lands / margin75. 80 / 176. A / 0.413077. 0.0156 / 1/64 / 178. angles / hardness79. length / shorter / blunter80. clearance81. equal / oversized / distorted82. feet per minute83. revolutions per minute84. feed / advancement / inches85. slow / heavy86. conical-shaped87. counterbore / concentric88. taper89. plug / blind / bottom90. bottoming91. conical / mark / start92. sharper / layout / center93. pin / drive / remove94. marking / layout / notChapter 11APPLICATION QUESTIONS1. 7162. 11323. #224. 19645. E and 14-in6. #2 (0.221)7. 8°8. 90°9. 1167 rpm10. 0.214 min or about 13 sChapter 11 REVIEW EXAM1. c 9. c2. b 10. d3. c 11. c4. a 12. c5. d 13. a6. a 14. d7. a 15. b8. b
142Student Study Guide / Aircraft Basic ScienceChapter 12 STUDY QUESTIONS1. hollow / long / wall2. rigid3. bent / formed / wall4. rubber / synthetic / hoses5. rigid / outside / wall6. tapered / wall7. weight / threads8. outside / wall9. fittings / connected10. 3711. double / thickness12. AN818 / AN819 / cone13. body / bulkhead / universal14. internal / pipe-to-AN15. rubber 16. sixteenths17. AN819-4 / AN819-1218. flareless / MS19. fittings / disconnections20. low / less / weight21. twice / operating22. inner / cotton / rubber23. yellow / lay24. manufacturer’s / size / manufacture25. cotton / stainless / cotton26. pneumatic / coolant / fuel27. tetrafluoroethylene / fluids28. 27267 / stainless29. two / triple30. carrying / dash31. removed / reused32. socket / nipple / sleeve33. replacement34. temperatures / abrasion35. material / diameter / thickness36. pattern37. expands / contracts38. radius / large39. inner40. small / 75 percent41. 14in.42. flange / gripped / gasket43. sleeve / nut44. 3845. sliding / hose / clamp46. fitting / sleeve / nut47. presetting / sleeve48. lubrication49. tubing / same50. oxygen51. soluble52. forced53. tightening / sheared54. overtighten / tubing / fittings55. clamp / socket / nipple56. notches / nipple / hex57. cover / end / notches58. ends / capped59. loosening / inspecting / damage60. one / six61. carbon / rust62. lay / straightening63. ball / freely64. preformed / straightened65. length / 5 / 866. radius / 1267. finger68. dark / cool69. flare / 10 / dent70. AND10375Chapter 12 APPLICATION QUESTIONS1. 0.840 in 6. AN818D102. 0.840 in 7. AN821-63. 0.622 in 8. AN919-124. 0.546 in 9. AN823-4-45. 22.7 percent 10. 9/16-18Chapter 12REVIEW EXAM1. c 7. a2. a 8. d3. d 9. d4. d 10.b5. a 11. a6. d 12. bChapter 13

  • Left Quote Icon

    Student Picture

  • Left Quote Icon

    Student Picture

  • Left Quote Icon

    Student Picture