B verify the trunks using show interfaces trunk

This preview shows page 4 - 7 out of 8 pages.

b. Verify the trunks using show interfaces trunkcommand on S1. S1# show interface trunkPortModeEncapsulation StatusNative vlan Fa0/1desirable802.1q trunking1 Fa0/3on802.1q trunking1 Port Vlans allowed on trunk Fa0/1 1-4094 Fa0/3 1-4094 Port Vlans allowed and active in management domain Fa0/1 1 Fa0/3 1 Port Vlans in spanning tree forwarding state and not pruned Fa0/1 none Fa0/3 none c. Configure a permanent trunk between S2 and S3. d. Record the commands you used to create the static trunk. S1(config)# interface f0/3 S2/3 (config-if)# switchport mode trunk Part 3: Add VLANs and Assign Ports Step 1: Add VLANs on the switches. a. On S1, add VLAN 10. S1(config)# vlan 10Were you able to create VLAN 10 on S1? Explain. NO. ITS IS A CLIENT b. On S2, add the following VLANs.
Lab Configure Extended VLANs, VTP, and DTP © 2017 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 5of 8VLAN Name 10 Red 20 Blue 30 Yellow 99 Management S2(config)# vlan 10S2(config-vlan)# name RedS2(config-vlan)# vlan 20S2(config-vlan)# name BlueS2(config-vlan)# vlan 30S2(config-vlan)# name Yellow S2(config-vlan)# vlan 99 S2(config-vlan)# name ManagementS2(config-vlan)# endS2# show vlan briefVLAN Name Status Ports ---- -------------------------------- --------- ------------------------------- 1 defaultactive Fa0/2, Fa0/4, Fa0/5, Fa0/6 Fa0/7, Fa0/8, Fa0/9, Fa0/10 Fa0/11, Fa0/12, Fa0/13, Fa0/14 Fa0/15, Fa0/16, Fa0/17, Fa0/18 Fa0/19, Fa0/20, Fa0/21, Fa0/22 Fa0/23, Fa0/24, Gi0/1, Gi0/2 10 Redactive 20 Blueactive 30 Yellowactive 99 Management<output omitted> active Step 2: Verify VTP updates on S1 and S3. Because S2 is configured as a VTP server, and S1 and S3 are configured as VTP clients, S1 and S3 should learn and implement the VLAN information from S2. What showcommands did you use to verify the VTP updates on S1 and S3? Show vtp status Step 3: Assign ports to VLANs. In this step, you will associate ports to VLANs and configure IP addresses according to the table below. Port Assignment VLAN Attached PC IP Address and Prefix S1 F0/6 VLAN 10 PC-A: 192.168.10.1 / 24
Lab Configure Extended VLANs, VTP, and DTP © 2017 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 6of 8S2 F0/18 VLAN 20 PC-B: 192.168.20.1 /24 S3 F0/18 VLAN 10 PC-C: 192.168.10.2 /24 a. On S1, configure F0/6 to access mode and assign F0/6 to VLAN 10. S1(config)# interface f0/6S1(config-if)# switchport mode accessS1(config-if)# switchport access vlan 10b. Repeat the procedure for switchport F0/18 on S2 and S3. Assign the VLAN according to the table above. c. Assign the IP addresses to the PCs according to the table above. Step 4: Configure IP addresses on the switches. a. On S1, assign an IP address to the SVI for VLAN 99 according to the Addressing Table and activate the interface. S1(config)# interface vlan 99S1(config-if)# ip address 192.168.99.1 255.255.255.0S1(config-fi)# no shutdownb. Repeat step a. for S2 and S3.

  • Left Quote Icon

    Student Picture

  • Left Quote Icon

    Student Picture

  • Left Quote Icon

    Student Picture