z After installation check that there is 2 3 mm 008 012in of play in the axial

Z after installation check that there is 2 3 mm 008

This preview shows page 17 - 21 out of 68 pages.

z After installation, check that there is 2 – 3 mm (0.08 – 0.12 in.) of play in the axial direction. z After installation, check that the drive shaft cannot be re- moved by hand. (b) Using a screwdriver, remove the snap ring from the in- board joint shaft. 8. REMOVE RH DRIVE SHAFT (a) Remove the bearing lock bolt. Torque: 32 N·m (330 kgf·cm, 24 ft·lbf) (b) Using pliers, remove the snap ring and drive shaft. HINT: At the time of installation, coat gear oil to the inboard joint shaft and differential case sliding surface.
Image of page 17
SA0E5–01 R14967 W03190 Matchmarks SA0689 SA–18 SUSPENSION AND AXLE FRONT DRIVE SHAFT 1066 AuthorĂ: DateĂ: 1997 LEXUS ES300 (RM511U) DISASSEMBLY 1. CHECK DRIVE SHAFT (a) Check to see that there is no play in the outboard joint shaft. (b) Check to see that the inboard joint shaft slides smoothly in the thrust direction. (c) Check to see that there is no remarkable play in the radial direction of the inboard joint shaft. (d) Check for damage to boots. 2. REMOVE INBOARD AND OUTBOARD JOINT BOOT CLAMPS (a) Using pliers, draw the hook together and remove the large inboard joint boot clamp and remove them. (b) Using a side cutter, cut the small inboard and 2 outboard joint boot clamps and remove them. 3. REMOVE INBOARD JOINT SHAFT FROM OUTBOARD JOINT SHAFT (a) Place matchmarks on the inboard and outboard joint shafts. NOTICE: Do not punch the marks. (b) Using a snap ring expander, pull out the outboard joint shaft expanding the snap ring. 4. REMOVE INBOARD AND OUTBOARD JOINT BOOTS Slide out the 2 boots. 5. LH DRIVE SHAFT: REMOVE DUST COVER Using a screwdriver and hammer, remove the dust cover from the inboard joint shaft. 6. RH DRIVE SHAFT: REMOVE DUST COVER Using a press, remove the dust cover from the inboard joint shaft.
Image of page 18
R09717 SST SA1451 SUSPENSION AND AXLE FRONT DRIVE SHAFT SA–19 1067 AuthorĂ: DateĂ: 1997 LEXUS ES300 (RM511U) 7. RH DRIVE SHAFT: DISASSEMBLE INBOARD JOINT SHAFT (a) Using SST and a press, remove the dust cover. SST 09950–00020 (b) Using a snap ring expander, remove the snap ring. (c) Using a press, remove the bearing. (d) Remove the snap ring. 8. REMOVE NO.2 DUST DEFLECTOR (a) Mount outboard joint shaft in a soft jaw vise. (b) Using a screwdriver and hammer, remove the No.2 dust deflector. NOTICE: Be careful not to damage the ABS speed sensor rotor.
Image of page 19
SA0E6–02 W02121 SST W03193 SST W03316 SST W03145 SST SST W03194 SST 100.5mm (3.957 in.) SA–20 SUSPENSION AND AXLE FRONT DRIVE SHAFT 1068 AuthorĂ: DateĂ: 1997 LEXUS ES300 (RM511U) REASSEMBLY 1. INSTALL NO.2 DUST DEFLECTOR Using SST and a press, install a new No.2 dust deflector. SST 09309–36010, 09316–20011 2. RH DRIVE SHAFT: ASSEMBLE INBOARD JOINT SHAFT (a) Install a new snap ring to the inboard joint shaft. (b) Using SST and a press, install a new bearing. SST 09223–56010 (c) Using a snap ring expander, install a new snap ring. (d) Using SST and a press, install a new dust cover. SST 09223–56010 3. LH DRIVE SHAFT: INSTALL DUST COVER Using SST and a press, install a dust cover.
Image of page 20
Image of page 21

You've reached the end of your free preview.

Want to read all 68 pages?

  • Spring '14
  • SST, Shock absorber, Suspension, Automotive suspension technologies

  • Left Quote Icon

    Student Picture

  • Left Quote Icon

    Student Picture

  • Left Quote Icon

    Student Picture