00 bolt hole circle yasnac g71 00 bolt hole arc

00 Bolt Hole Circle (Yasnac)
G71 00 Bolt Hole Arc (Yasnac)
G72 00 Bolt Holes Along an Angle (Yasnac)
G73 09 High Speed Peck Drill Canned Cycle
G74 09 Reverse Tap Canned Cycle
G76 09 Fine Boring Canned Cycle
G77 09 Back Bore Canned Cycle
(M codes continued next page)

20
JUNE 2000 PROGRAMMING
Code: Group: Function:
G80 * 09 Canned Cycle Cancel
G81 09 Drill Canned Cycle
G82 09 Spot Drill Canned Cycle
G83 09 Regular Peck Drill Canned Cycle
G84 09 Tapping Canned Cycle
G85 09 Bore in/Bore out Canned Cycle
G86 09 Bore in/Stop/Rapid out Canned Cycle
G87 09 Bore in/Manual Retract Canned Cycle
G88 09 Bore/Dwell/Manual Retract Canned Cycle
G89 09 Bore/Dwell/Bore out Canned Cycle
G90 * 03 Absolute
G91 03 Incremental
G92 00 Set Work Coordinates
G93 05 Inverse Time Feed Mode
G94 * 05 Feed Per Minute Mode
G98 * 10 Initial Point Return
G99 10 R Plane Return
G100 00 Cancle Mirror Image
G101 00 Enable Mirror Image
G102 00 Programmable Output to RS-232
G103 00 Limit Block Buffering (Block Lookahead)
G107 00 Cylindrical Mapping
G110 12 Select Work Coordinate System 7
G111 12 Select Work Coordinate System 8
G112 12 Select Work Coordinate System 9
G113 12 Select Work Coordinate System 10
G114 12 Select Work Coordinate System 11
G115 12 Select Work Coordinate System 12
G116 12 Select Work Coordinate System 13
G117 12 Select Work Coordinate System 14
G118 12 Select Work Coordinate System 15
G119 12 Select Work Coordinate System 16
G120 12 Select Work Coordinate System 17
G121 12 Select Work Coordinate System 18
G122 12 Select Work Coordinate System 19
G123 12 Select Work Coordinate System 20
(M codes continued next page)

21
JUNE 2000 PROGRAMMING
Code: Group: Function:
G124 12 Select Work Coordinate System 21
G125 12 Select Work Coordinate System 22
G126 12 Select Work Coordinate System 23
G127 12 Select Work Coordinate System 24
G128 12 Select Work Coordinate System 25
G129 12 Select Work Coordinate System 26
G136 00 Automatic Work Offset Center Measurement
G141 07 3D+ Cutter Compensation
G143 08 5 Axis Tool Length Compensation (optional)
G150 00 General Purpose Pocket Milling
G174 00 Special Purpose Rigid Tapping CCW
G184 00 Special Purpose Rigid Tapping CW
G187 00 Accuracy Control for High Speed Machining
Each G code defined in this control is part of a group of G codes. The Group 0 codes
are non-modal; that is, they specify a function applicable to that block only and do
not affect other blocks. The other groups are modal and the specification of one
code in the group cancels the previous code applicable from that group. A modal G
code applies to all subsequent blocks so those blocks do not need to re-specify the
same G code.
There is also one case where the Group 01 G codes will cancel the Group 9 (canned
cycles) codes. If a canned cycle is active (G73 through G89), the use of G00 or G01
will cancel the canned cycle.

22
JUNE 2000 PROGRAMMING
MACHINE DEFAULTS
A default is an automatic function of the machine tool control. After powering up the
machine, the control will recognize the default G code values. The machine will
go to the part zero that was entered in for G54 if no other work coordinate code was
specified in the actual program, because the machine automatically recognizes the