c Surely install the fuel hose clamp to the fuel filter with click sound d

C surely install the fuel hose clamp to the fuel

This preview shows page 23 - 30 out of 66 pages.

(c)Surely install the fuel hose clamp to the fuel filter with”click” sound. (d)After installing the clamp, check that the clamp is fixed bypulling up the clamp. 3. INSTALL AIR ASSIST HOSES AND PIPE (a) Connect the air assist hoses to the intake manifold. (b) Install the air assist pipe to the bracket on the No.1 fuel pipe. 4. CONNECT INJECTOR CONNECTORS 5. INSTALL AIR INTAKE CHAMBER ASSEMBLY (See page EM–52 ) 6. INSTALL AIR CLEANER HOSE 7. CHECK FOR FUEL LEAKS
Image of page 23
SF05U–01 SF–24 SFI FUEL TANK AND LINE 875 AuthorĂ: DateĂ: 1997 LEXUS ES300 (RM511U) FUEL TANK AND LINE PRECAUTION 1. Always use new gaskets when replacing the fuel tank or component parts. 2. Apply the proper torque to all parts tightened.
Image of page 24
SF05V–04 S04763 The Location of Fuel Tank Cushion No.1 Fuel Tank Protector Fuel Tank Vent Tube Set Plate Fuel Pump Fuel Outlet Tube Fuel Tank Fuel Inlet Hose Fuel Inlet Pipe Shield Fuel Tank Cap Gasket Bracket Fuel Inlet Pipe Bracket Fuel Inlet Pipe Protector Gasket 39 (400, 29) 56 (570, 41) 44 (450, 33) 56 (570, 41) Heat Insulator Center Exhaust Pipe Heated Oxygen Sensor (Bank 1 Sensor 2) Fuel Tank Band Gasket N·m (kgf·cm, ft·lbf) : Specified torque Non–reusable part Heated Oxygen Sensor (Bank 1 Sensor 2) HINT: z Before installing the heated oxygen sensor, twist the sensor wire counterclockwise 3 and 1/2 turns. z After installing the heated oxygen sensor, check that the sensor wire is not twisted, If it is twisted, remove the heated oxygen sensor and reinstall it. Gasket x8 4 (40, 35 in.·lbf) SFI FUEL TANK AND LINE SF–25 876 AuthorĂ: DateĂ: 1997 LEXUS ES300 (RM511U) COMPONENTS
Image of page 25
SF05W–01 BO0919 Crack Leakage Deformation Z10162 SST Use SST 28 N·m (285 kgf·cm, 21 ft·lbf) Fulcrum Length 30 cm (11.81 in) SST: 09631–22020 FU0041 Pipe 2 – 7 mm (0.08 – 0.28 in.) Hose Clip 0 – 3 mm (0 – 0.12 in.) SF–26 SFI FUEL TANK AND LINE 877 AuthorĂ: DateĂ: 1997 LEXUS ES300 (RM511U) INSPECTION INSPECT FUEL TANK AND LINE (a) Check the fuel lines for cracks or leakage, and all connec- tions for deformation. (b) Check the fuel tank vapor vent system hoses and connec- tions for looseness, sharp bends or damage. (c) Check the fuel tank for deformation, cracks, fuel leakage or tank band looseness. (d) Check the filler neck for damage or fuel leakage. (e) Hose and pipe connections are as shown in the illustra- tion. If a problem is found, repair or replace the parts as necessary.
Image of page 26
S04539 MAF Meter MAF Meter Connector z Gasket z Non–reusable part SF05X–01 SFI MASS AIR FLOW (MAF) METER SF–27 878 AuthorĂ: DateĂ: 1997 LEXUS ES300 (RM511U) MASS AIR FLOW (MAF) METER COMPONENTS
Image of page 27
SF05Y–06 S04755 SF–28 SFI MASS AIR FLOW (MAF) METER 879 AuthorĂ: DateĂ: 1997 LEXUS ES300 (RM511U) REMOVAL REMOVE MAF METER (a) Disconnect the MAF meter connector. (b) Remove the 2 bolts, MAF meter and gasket. HINT: At the time of installation, please refer to the following item. Use a new gasket.
Image of page 28
SF05Z–04 S04526 E2 THA Ohmmeter S04756 Air VG E2G Voltmeter SFI MASS AIR FLOW (MAF) METER SF–29 880 AuthorĂ: DateĂ: 1997 LEXUS ES300 (RM511U) INSPECTION 1. INSPECT MAF METER RESISTANCE Using an ohmmeter, measure the resistance between terminals THA and E2.
Image of page 29
Image of page 30

You've reached the end of your free preview.

Want to read all 66 pages?

  • Spring '14
  • Lexus, Fuel injection, SFI, LEXUS ES300, Throttle position sensor

  • Left Quote Icon

    Student Picture

  • Left Quote Icon

    Student Picture

  • Left Quote Icon

    Student Picture