Auto Detect Motor and Sensor 4 Input Pin 1 ADC 5 V PU Pin 2 IO PUPD Pin 3

Auto detect motor and sensor 4 input pin 1 adc 5 v pu

  • Homework Help
  • mashfiq
  • 47
  • 100% (2) 2 out of 2 people found this document helpful

This preview shows page 42 - 44 out of 47 pages.

Auto Detect Motor and Sensor 4 Input Pin 1: ADC 5 V PU Pin 2: I/O, PU,PD Pin 3: Ground Pin 4: 5 Volt +20 mA Pin 5: I/O, PU, SCK(I2C), UART(TX) Pin 6: I/O, ADC 5 V, PD, SDA(I2C), UART(RX) Auto detect Sensor and Motor USB Client 1,5 , 12 and 480 MBit USB Host 1,5, 12 Mbit 5 Volt +500 mA (1,2A MAX) Current limiter Apple Autentic IC + Decoding MCU 9V battery 5 V buck boost 2 A> 3V3 1 A 1V8 1 A 1V2 1 A Power up sequence 5 V Current limiter 5V on/off Current measurement on overall current Voltage check on Batteries 5V BURN OUT Buttons Diodes are on the KEYPAD PCB TIAM1808 See page 6 See page 2 and 3 See page 4 See page 2 and 3 See page 2 and 3 See page 5 Note: PU = Pull Up PD = Pull Down SDA = Seriel DATA SCK = Seriel Clock ADC = Analog Digital Converter USB = Universial Serial Bus UART = Universal Asynchronous Receiver/Transmitter PWM = Pulse Wide Modulation GUI = Graphical User Interface B&W = Black and White mDDR = Mobile Double Data Rate synchronous DRAM R = Red G = Green uSD = micro Secure Digital I2C = Inter-Integrated Circuit SPI = Serial Peripheral Interface Bus PCB = Printed Circuit Board of Title Project Number Engineer/constructer Schematic Name Date (YYYY/MM/DD) Drafter Date (YYYY/MM/DD) Sheet Page Size Version 1 6 A2 95647_20 BHP 95647_20J BHP/JU J 2012/09/07 95647 2012/09/07
Image of page 42
5 5 4 4 3 3 2 2 1 1 D D C C B B A A SD/uSD CARDINTERFACE Connector to KEYPAD PCB TO/FROM PAGE 3 TO/FROM PAGE 4 BOOT[7:0] Boot Mode AIS 0000 0010 NOR Yes 0000 1110 NAND 8 Yes 0001 0000 NAND 16 Yes 0000 0000 I2C0 EEPROM Yes 0000 0110 I2C1 EEPROM Yes 0000 0001 I2C0 Slave Yes 0000 0111 I2C1 Slave Yes 0000 1000 SPI0 EEPROM Yes 0000 1001 SPI1 EEPROM Yes 0000 1010 SPI0 Flash Yes 0000 1100 SPI1 Flash Yes 0001 0010 SPI0 Slave Yes 0001 0011 SPI1 Slave Yes xxx1 0110 UART0 Yes xxx1 0111 UART1 Yes xxx1 0100 UART2 Yes 0000 0100 HPI No 0001 1110 Emulation Debug No SPI setup SPI0 Flash and ADC SPI1 Display I2C0 EEPROM UART UART0 input RJ12 UART1 input RJ12 UART2 BT RX,TX,CTS,RTS SW UART input PRU SW UART input PRU Possible alternative boot Flash SPI Possible alternative boot Flash SPI RED RED GREEN GREEN DEFAULT ON DEFAULT ON DEFAULT OFF DEFAULT OFF When Write Control (WC) is driven High. When unconnected, the signal is internally read as VIL, and Write operations are allowed. NC = M3, M14, N16 MAX 1 MHz TO/FROM PAGE5 TO/FROM PAGE6 SOUNDEN INTERNAL PD Short wire twisted to speaker Speaker SPI - FLASH MAX 104 MHz I/O for Debug NM NM Rechargeable Battery Detect Switch GP6_11, 6_12 and 6_13 not be moved 2 green diodes, internal PU NM = NOT MOUNTED WE Botten Side Botten Side Botten Side Botten Side NM - Part of Mech. BOM NM NM NM NM NM DAT0 DAT1 MCI0_DA1 MCI0_DA2 MCI0_DA3 MCI0_CK MCI0_CDA MCI0_DA0 DIODE3 DIODE2 DIODE0 DIODE2 SOUNDEN TXINA_EN TXINB_EN TXINC_EN TXINA TXINB TXINC TXIND RXINA_EN RXINB_EN RXINC_EN RXINA RXINB RXINC RXIND ADCCLK ADCCS ADCMOSI ADCMISO LEGDETB LEGDETC LEGDETD I_ONA DIGIA1 DIGIA0 I_ONB DIGIB1 DIGIB0 I_ONC DIGIC1 DIGIC0 I_OND DIGID1 DIGID0 MAPWM MBPWM INTD0 MDPWM MCPWM TXINA TXINB RXINA RXINB RXINC RXIND FMISO ADCMISO FMOSI ADCMOSI SCKDIS CSDIS MOSIDIS MISODIS MBPWM LEGDETD MAPWM RXIND_EN TXIND_EN RXINC_EN TXINC_EN MCPWM DIGIA1 MDPWM I_ONA DIGIB0 I_ONC LEGDETB ADCCS TXINC TXIND DIGIC1 DIGID1
Image of page 43
Image of page 44

You've reached the end of your free preview.

Want to read all 47 pages?

  • Fall '07
  • walker
  • ........., The LEGO Group, EV3 brick

  • Left Quote Icon

    Student Picture

  • Left Quote Icon

    Student Picture

  • Left Quote Icon

    Student Picture

Stuck? We have tutors online 24/7 who can help you get unstuck.
A+ icon
Ask Expert Tutors You can ask You can ask You can ask (will expire )
Answers in as fast as 15 minutes