HINT After installing the oil seal rings check that they move smoothly 2

Hint after installing the oil seal rings check that

This preview shows page 89 - 96 out of 139 pages.

HINT: After installing the oil seal rings, check that they move smoothly. 2. INSTALL C0 ACCUMULATOR PISTON TO OVER- DRIVE CASE (a) Install a new O-ring to the accumulator piston. (b) Coat the O-ring with ATF. (c) Install the accumulator piston, 2 springs and retaining plate. (d) Using snap ring pliers, install the snap ring. AX042-02
Image of page 89
AUTOMATIC TRANSAXLE OVERDRIVE UNIT - AX-72 OVERDRIVE BRAKE ASSEMBLY 1. INSTALL PISTON INTO DRUM (a) Install new O-rings to the piston. Coat the new O-rings with ATF. (b) Press the piston into the drum, being careful not to dam- age the O-rings. 2. INSTALL FLANGE, DISCS AND PLATES Install the flange, discs and plates. Install in order: P=Plate D=Disc Flange-D-P-D-P-D-P 3. POSITION PISTON RETURN SPRING AX043-05
Image of page 90
AUTOMATIC TRANSAXLE OVERDRIVE UNIT - AX-73 4. INSTALL SNAP RING INTO CASE Be sure the end gap of the snap ring is not aligned with one of cutouts. 5. INSTALL OVERDRIVE PLANETARY GEAR ONTO OV- ERDRIVE DIRECT CLUTCH While turning the overdrive planetary gear clockwise, install it onto the overdrive direct clutch. HINT: If the overdrive planetary gear is properly installed onto the direct clutch, the counter drive gear height from the overdrive case will be about 24 mm (0.94 in.).
Image of page 91
AUTOMATIC TRANSAXLE VALVE BODY - AX-74 VALVE BODY COMPONENTS VALVE BODY DISASSEMBLY NOTICE: When disassembling the valve body, be careful not to damage or deform the plate which overhangs the valve body. 1. REMOVE SOLENOIDS (a) Remove No.1 and No.2 solenoids with the retainer. NOTICE: When removing the solenoid, do not use a screw- driver, etc. to pry up the solenoid. (b) Remove the O-ring from each solenoid. (c) Remove the No.3 solenoid. (d) Remove the O-ring from the solenoid. AX044-02 AX0TW-01
Image of page 92
AUTOMATIC TRANSAXLE VALVE BODY - AX-75 2. REMOVE LOCK PLATE 3. REMOVE B 0 ACCUMULATOR ASSEMBLY (a) Remove the 3 bolts. (b) Remove the B 0 accumulator assembly. 4. DISASSEMBLE B 0 ACCUMULATOR ASSEMBLY (a) Applying compressed air to the cylinder hole, remove the piston and spring. (b) Remove the 2 O-rings from the piston. 5. REMOVE NO.4 SOLENOID (a) Remove the No.4 solenoid. (b) Remove the O-ring from the solenoid. 6. REMOVE NO.1 LOWER VALVE BODY COVER Remove the 5 bolts and No.1 lower valve body cover.
Image of page 93
AUTOMATIC TRANSAXLE VALVE BODY - AX-76 7. REMOVE OIL STRAINER, NO.1 LOWER VALVE BODY COVER GASKETS AND CHECK VALVE (a) Remove the 2 gaskets and plate from the lower valve body. (b) Remove the oil strainer, check valve and spring. 8. REMOVE PRESSURE RELIEF VALVE 9. REMOVE NO.2 LOWER VALVE BODY COVER, OIL STRAINER, CHECK BALLS AND VIBRATING STOP- PER Remove the 11 bolts and lower valve body cover. (b) Remove the 2 check balls, oil strainer and vibrating stop- per.
Image of page 94
AUTOMATIC TRANSAXLE VALVE BODY - AX-77 10. REMOVE NO.2 LOWER VALVE BODY COVER GAS- KETS AND CHECK BALLS (a) Remove the 2 screws from the lower valve body cover.
Image of page 95
Image of page 96

  • Left Quote Icon

    Student Picture

  • Left Quote Icon

    Student Picture

  • Left Quote Icon

    Student Picture