E enable the g01 interface on the cust1 router and

This preview shows page 3 - 5 out of 10 pages.

e. Enable the G0/1 interface on the Cust1 router and observe the debug output as the PPPoE dialer session is established and CHAP authentication takes place.
Lab Configuring a Router as a PPPoE Client for DSL Connectivity © 2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 4of 10*Jul 30 19:29:03.839: Sending PADI: Interface = GigabitEthernet0/1 *Jul 30 19:29:03.839: PPPoE 0: I PADO R:30f7.0da3.0b01 L:30f7.0da3.0bc1 Gi0/1 *Jul 30 19:29:05.887: PPPOE: we've got our pado and the pado timer went off *Jul 30 19:29:05.887: OUT PADR from PPPoE Session *Jul 30 19:29:05.895: PPPoE 1: I PADS R:30f7.0da3.0b01 L:30f7.0da3.0bc1 Gi0/1 *Jul 30 19:29:05.895: IN PADS from PPPoE Session *Jul 30 19:29:05.899: %DIALER-6-BIND: Interface Vi2 bound to profile Di1 *Jul 30 19:29:05.899: PPPoE: Virtual Access interface obtained. *Jul 30 19:29:05.899: PPPoE : encap string prepared *Jul 30 19:29:05.899: [0]PPPoE 1: data path set to PPPoE Client *Jul 30 19:29:05.903: %LINK-3-UPDOWN: Interface Virtual-Access2, changed state to up *Jul 30 19:29:05.911: Vi2 PPP: Using dialer call direction *Jul 30 19:29:05.911: Vi2 PPP: Treating connection as a callout *Jul 30 19:29:05.911: Vi2 PPP: Session handle[C6000001] Session id[1] *Jul 30 19:29:05.919: Vi2 PPP: No authorization without authentication *Jul 30 19:29:05.939: Vi2 CHAP: I CHALLENGE id 1 len 24 from "ISP" *Jul 30 19:29:05.939: Vi2 PPP: Sent CHAP SENDAUTH Request *Jul 30 19:29:05.939: Vi2 PPP: Received SENDAUTH Response FAIL *Jul 30 19:29:05.939: Vi2 CHAP: Using hostname from interface CHAP *Jul 30 19:29:05.939: Vi2 CHAP: Using password from interface CHAP *Jul 30 19:29:05.939: Vi2 CHAP: O RESPONSE id 1 len 26 from "Cust1" *Jul 30 19:29:05.955: Vi2 CHAP: I SUCCESS id 1 len 4 *Jul 30 19:29:05.955: %LINEPROTO-5-UPDOWN: Line protocol on Interface Virtual-Access2, changed state to up *Jul 30 19:29:05.983: PPPoE : ipfib_encapstr prepared *Jul 30 19:29:05.983: PPPoE : ipfib_encapstr prepared f. Issue a show ip interface brief command on the Cust1 router to display the IP address assigned by the ISP router. Sample output is shown below. By what method was the IP address obtained? _________________ PPP Cust1# show ip interface briefInterface IP-Address OK? Method Status Protocol Embedded-Service-Engine0/0 unassigned YES unset administratively down down GigabitEthernet0/0 unassigned YES unset administratively down down GigabitEthernet0/1 unassigned YES unset up up Serial0/0/0 unassigned YES unset administratively down down Serial0/0/1 unassigned YES unset administratively down down Dialer1 10.0.0.1 YES IPCP up up Virtual-Access1 unassigned YES unset up up Virtual-Access2 unassigned YES unset up up g. Issue a show ip routecommand on the Cust1 router. Sample output is shown below.

  • Left Quote Icon

    Student Picture

  • Left Quote Icon

    Student Picture

  • Left Quote Icon

    Student Picture