Quick Guide to Proto-Board PB-503
Figure 1.
The PB-503 Analog/Digital Proto-Board (Fig. 1) contains a large breadboard area (white area in center) on which you will be laying out your circuits for the first half of this semester. PB-503 also provide
ECE 2100: Electrical and Computer Engineering II
Course Description
Introduction to the theory and practice of discrete systems using difference equations and z-transforms, and
analog systems using differential equations and Laplace transforms.
Transcript
Tektronix CFG 280 Function Generator
The CFG280 is capable of generating triangle, sine, or square waves. The frequency of the output is variable from approximately l Hz to 100 MHz. The frequency and amplitude controls are shown on the graph. The ou
Operation of the square/triangular wave oscillator
An operation amplifier circuit that creates both a square wave and a triangular wave is comprised of three separate stages as shown in Figure 1: 1) the positive feedback op-amp known as the Schmitt t
LF353 Wide Bandwidth Dual JFET Input Operational Amplifier
February 1995
LF353 Wide Bandwidth Dual JFET Input Operational Amplifier
General Description
These devices are low cost high speed dual JFET input operational amplifiers with an internally
Name _ ECE 2100 Op-Amp Circuits Lab 5 Week 1 Using Google, look up the input bias current for the LF353 op-amp and predict the time rate of change of the output voltage for the circuit below - after the switch opens.
Input Bias Current = 50pA ; C =
ECE 2100 Laboratory 6The Op-Amp Monologues
Introduction In these three-week laboratories we will use a common building block of circuit design called the operational amplier or op-amp. This is an integrated circuit consisting of numerous transistors
ECE 2100 Laboratory 1
The main purpose of this lab is to familiarize you with the lab work benches and to demonstrate the most basic functions of the measurement apparatus. Additionally you will verify Ohms Law and the voltage and current divider pri
Arun Swain aps97 ECE 2100 HW #10 To create a bandpass filter, we used a combination of low pass and high pass filters. We started off by building a high pass with a gain of 10 and then connected its output as the input to a low pass filter. The high
ECE 2100
Fall 2008
Introduction to Circuits for Electrical and Computer Engineers
Homework Assignment #12 {Last homework assignment for the course!} Due Friday 11/21/08 9:00 AM Please complete all of problems: P12.1, 12.2, 12.3, 12.5, 12.9, 12.14 [
ECE 2100
Fall 2008
Introduction to Circuits for Electrical and Computer Engineers
Homework Assignment #12 revised Last homework assignment for the course! Due Friday 11/21/08 9:00 AM (Deposit your homework on the desk at the front of the room at th
ECE 2100
Fall 2008
Introduction to Circuits for Electrical and Computer Engineers
Homework Assignment #11 Due Friday 11/14/08 9:00 AM (Deposit your homework on the desk at the front of the room at the beginning of class in Kimball B11) Please do no
ECE 2100
Fall 2008
Introduction to Circuits for Electrical and Computer Engineers
Homework Assignment #10 Due Friday 11/7/08 9:00 AM (Deposit your homework on the desk at the front of the room at the beginning of class in Kimball B11) Please do not
ECE 2100
Fall 2008
Introduction to Circuits for Electrical and Computer Engineers
Homework Assignment #9 Due Friday 10/31/08 9:00 AM (Deposit your homework on the desk at the front of the room at the beginning of class in Kimball B11) Please do not
ECE 2100
Fall 2008
Introduction to Circuits for Electrical and Computer Engineers
Homework Assignment #6 Due Friday 10/10/08 9:00 AM (Deposit your homework on the desk at the front of the room at the beginning of class in Kimball B11) Please do not
ECE 2100
Fall 2008
Introduction to Circuits for Electrical and Computer Engineers
Homework Assignment #4 Due Friday 9/26/08 9:00 AM (Deposit your homework on the desk at the front of the room at the beginning of class in Kimball B11) All of this we