Department of Electrical Engineering and Computer Science
HE 102: Introduction to Computer Engineering
Homework #1
Due Date: (in-class) Monday, September 19, 2011
Problem 1: From text 1.10
Convert into hexadecimal and then to binary
(a) 130537510 =
(b
9/25/2011
EE 102: INTRODUCTION TO
COMPUTER ENGINEERING
Lecture 7: Combination Logic
Circuit Design - 1
9/28/2011
Avinash Kodi, [email protected]
Combinational Circuits
2
System of interconnected logic gates whose
outputs at any time are determined by
combinin
9/8/2011
EE 102: INTRODUCTION TO
COMPUTER ENGINEERING
Lecture 2: Number System
9/9/2011
Avinash Kodi, [email protected]
Course Administration
2
Lecture Notes 1 and 2 are posted
Lab 1 handout and report posted
Class Webpage Access
Username:
ee102
Password: f
9/21/2011
EE 102: INTRODUCTION TO
COMPUTER ENGINEERING
Lecture 5: Boolean Algebra - 2
Simplification Rules
09/21/2011
Avinash Kodi, [email protected]
Course Administration
2
Homework 2 is due Friday 9/30
Prepare for Quiz 2 Surprise Quiz!
Practice Problem 1 po
Revised March 2000
DM74LS00
Quad 2-Input NAND Gate
General Description
This device contains four independent gates each of which
performs the logic NAND function.
Ordering Code:
Order Number
Package Number
Package Description
DM74LS00M
M14A
14-Lead Small
EE 102
Introduction to Computer Engineering
Summer 2009
Laboratory 2: Basic Logic Gates
Purpose
The purpose of this lab is to investigate the behavior of basic logic gates and to experimentally derive
truth tables for Boolean expressions.
Equipment
1 IDL-
EE 101
Introduction to Electrical Engineering
Experiments #7: Circuit Construction, PHASES TWO
The purpose of this lab is to give student experience in the construction, testing,
troubleshooting and analysis of physical electrical circuits.
Equipment Need
EE 101
EE 101
Introduction to Electrical Engineering
Experiment #6: Circuit Construction, PHASE ONE
In Phase Zero you learned how to solder and you connected the switch and the battery snap to your
board. The single-pole double-throw (SPDT) switch is the
EE 101
Introduction to Electrical Engineering
Experiment #5: Circuit Construction, PHASE ZERO
The purpose of this lab is to give student experience in the construction, testing,
troubleshooting and analysis of physical electrical circuits.
Equipment Neede
10/17/2011
EE 102: INTRODUCTION TO
COMPUTER ENGINEERING
Lecture 10: Sequential Logic 1
Latches
10/17/2011
Avinash Kodi, [email protected]
Course Administration
2
No class on Friday 10/21 due to retreat
Homework 4 posted due on Friday 10/28
Lab 6 posted, pre-l
Department of Electrical Engineering and Computer Science
Ohio University
Fall 2011
EE 102: Introduction to Computer Engineering
Homework #2
Due Date: (in-class) Friday September 30, 2011
Problem 1: From text 2.11
Simplify each of the following expression
Department of Electrical Engineering and Computer Science
Ohio University
Fall 2011
EE 102: Introduction to Computer Engineering
Homework #1
Due Date: (in-class) Monday, September 19, 2011
Problem 1: From text 1.10
Convert into hexadecimal and then to bin
Department of Electrical Engineering and Computer Science
Ohio University
Fall 2011
EE 102: Introduction to Computer Engineering
Homework #3
Due Date: (in-class) Monday October 17, 2011
Problem 1: From text 5.3
Problem 2: From text 5.4
Problem 3: From tex
EE 101 Introduction to Electrical Engineering
Homework 6
Due: Monday, Oct 14, 2011 at 12:10 am (no exceptions without a valid excuse)
1.
Two batteries are placed in series to power a light bulb as shown below.
a)
b)
2.
Calculate the voltage across the lig
9/7/2011
EE 102: INTRODUCTION TO
COMPUTER ENGINEERING
Lecture 1: Introduction
9/7/2011
Avinash Kodi, [email protected]
Acknowledgement: A. J. Han Vinck
Agenda
2
Go over the syllabus
Introduction to Digital Systems
1
9/7/2011
Digital Devices
3
Pentium - 4
180
Design problem pi/ k-mapderive Boolean expressionrealize circuit
Analysis given a circuitstart determining input/how many-what is output of each gate-what is overall output
T FF: Q+ = T Q = Q Q+
001 011 010 110 111 101 100
C B A
0 0 0
0 0 1
0 1 0
0 1 1
1
10/19/2011
EE 102: INTRODUCTION TO
COMPUTER ENGINEERING
Lecture 11: Sequential Logic 2
Flip-Flops
10/19/2011
Avinash Kodi, [email protected]
Course Administration
2
No class on Friday 10/21
Homework 4 is due on Friday 10/28
1
10/19/2011
Flip-Flops
3
Latches s
Soldering Test (Written)
Read through the Weller WLC100 Electronic soldering station instructions and the chapter on
soldering and answer the following questions:
1. What is a cold solder joint and what can be done to prevent one from occurring?
2. What p
EE 101
Introduction to Electrical Engineering
Experiment #5: Circuit Analysis and Components Functionality
The purpose of this handout is to is develop understanding of the circuit functionality at
different engineering level.
System Level
Description of
FundamenTa/s of E/ecimb Circuffs/
Lecture
Circuit Elements
Dr. Wajciech Janwisienczak
Circuits Diagram
Circuit diagrams are a pictorial way of showing circuits.
Electricians and engineers draw circuit diagram: to help them
design the actual circuits. Here