THE UNIVERSITY of TENNESSEE
Industrial & Systems Engineering
IE 483 Introduction to Reliability Engineering
Quiz 9
Question 1)
Three communication channels in parallel have independent failure modes of 0.1
failures per hour. These components must share a
THE UNIVERSITY of TENNESSEE
Industrial & Systems Engineering
IE 483 Introduction to Reliability Engineering
Quiz 7
Question 1)
For the given system below, what is the system reliability? Assume independent failures.
Please round your answer to 3 decimals.
THE UNIVERSITY of TENNESSEE
Industrial & Systems Engineering
IE 483 Introduction to Reliability Engineering
Quiz 6
Question 1)
Failure rate for item A is 0.002 failures/hr, item B is 0.0003 failures/hr and item C is
0.001 failure/hr. The components are se
THE UNIVERSITY of TENNESSEE
Industrial & Systems Engineering
IE 483 Introduction to Reliability Engineering
Quiz 8
Question 1)
Determine the reliability of the system. Report the reliability up to four significant digits.
Answer:
If d fails:
Rsys = Ra*Rb*
THE UNIVERSITY of TENNESSEE
Industrial & Systems Engineering
IE 483 Introduction to Reliability Engineering
Assignment 9
Covering Lecture 9
Note: Please upload your entire assignment as one file. Pictures taken with a camera
must be pasted onto a word doc
THE UNIVERSITY of TENNESSEE
Industrial & Systems Engineering
IE 483 Introduction to Reliability Engineering
Assignment 7
Covering Lecture 7
Note: Please upload your entire assignment as one file. Pictures taken with a camera
must be pasted onto a word doc
THE UNIVERSITY of TENNESSEE
Industrial & Systems Engineering
IE 483 Introduction to Reliability Engineering
Assignment 8
Covering Lecture 8
Note: Please upload your entire assignment as one file. Pictures taken with a camera
must be pasted onto a word doc
THE UNIVERSITY of TENNESSEE
Industrial & Systems Engineering
IE 483 Introduction to Reliability Engineering
Assignment 10
Covering Lecture 10
Note: Please upload your entire assignment as one file. Pictures taken with a camera
must be pasted onto a word d
24.962
Page 1
2/9/05
Assignment 2
Due Wed 216 2005
Analyze the following data providing constraints and rankings relevant to the analysis of
Sanskrit desiderative reduplication. (Some modifications have been introduced in the data to
simplify the analysi
Exercises for Chapter 6 Control charts for variables
1 A highvoltage power supply should have a nominal output voltage of 350 V. A sample of four
units is selected each day and tested for processcontrol purposes. The data shown in the table
give the dif
Preparations for Exam 1 (Chapter 1)
1. What are the eight ways for understanding the quality of product or service?
1.
2.
3.
4.
5.
6.
7.
8.
Performance
Reliability
Durability
Serviceability
Aesthetics
Features
Perceived Quality
Conformance to Standards

Prepare for Exam III (Chapter 7)
Important: Homework, especially Homework 7(b) Problem 2.
1. What is the fraction nonconforming (definition)?
The fraction nonconforming is defined as the ratio of the number of nonconforming items in a
population to the to
StemandLeaf Plots in Excel
By Joseph Schmuller from Statistical Analysis with Excel For Dummies, 3rd Edition
Stemandleaf displays organize data so that an entire distribution of scores is quickly and easily
comprehensible. The display breaks each scor
Homework for Control Charts for Fraction Nonconforming
Assigned date: October 27 (Tuesday)
Due date: November 3 (Tuesday)
Requirements: Please turn in the hardcopy.
Problem 1. The numbers of nonconforming switches in samples of size 150 are shown in the
t
Prepare for Exam (Chapter 5 Introduction to Control Charts)
What are the center line, upper control limitation, lower control limitation of Shewhart
Control Chart Model?
Please list the at least two potential signals (indications) of outofcontrol proces
Preparations for Exam 1 (Chapter 1)
1. What are the eight ways for understanding the quality of product or service?
2. What are the three components (activities) of quality management?
3. What process does the most implementation of sixsigma use for proj
IE 603
TOPIC 3
Latin Square Design with Replications
LATIN SQUARES DESIGN
Yijk
k ijk
i j
Block
Position
Treatment
Positions
Blocks
1
2
3
4
1
2
3
4
A
B
C
D
B
C
D
A
D
C
D
A
B
C
B
A
Y243
1
2
3
1
A
B
C
D
2
3
B
C
A
D
D
A
C
B
4
D
C
B
A
22 17
4
22 27
14
16
29
ISE 405
ENGINEERING ECONOMIC ANALYSIS
JAN. 2016
Chapter 2
Outline:
Engineering Costs
Cost Estimating and Estimating Models
Objective:
Understand various cost concepts
Understand various cost estimation models
Be able to estimate engineering costs w
Chapter 3
INTEREST AND EQUIVALENCE
1
Where economic decisions are immediate we need
to consider:
amount of expenditure
Taxes
Where economic decisions occur over a
considerable period of time we also need to
consider:
interest
inflation
2
Money has
Chapter 4
MORE INTEREST FORMULAS
1
Calculation of P and F are fundamental.
Some problems are more complex and require an
understanding of added components:
Uniform series.
Arithmetic or geometric gradients.
Nominal and effective interest rates
Conti
170 El Chapter 5 Present Worth Analysis
Solution: The analysis period can conveniently be selected as the useful life of the devices,
ce both devices cost $1000, we have a situation where, in choosing either
or ﬁve years. Sin
he appropriate decision crite
Alex bought $1000 worth of home furniture. If
the items are expected to last 10 years, what
will the equivalent uniform annual cost be if
interest is 7%
Equivalent Uniform Annual Cost = EUAC = PWC(A/P, i, n)
Equivalent Uniform Annual Benefit = EUAB = PWB(
IE 430/591 Supply Chain Engineering
Quiz 3 (5 points in total), 35 minutes, October 1, 2015
Name:
NetID:
Short Answers (0.8 point each)
1.
Please briefly discussion on the impact of online sales on flexible pricing, production
portfolio, and promotion.
Th
Q.2
1. What are some keysuccess factors in diamond retailing? How do Blue Nile, Zales,
and Tiffany compare on those dimensions?
When analyzing retailers, the key success factors in diamond retailing can be measured
by customer service factors and cost fa
PyroSim User Manual
2014
PyroSim User Manual
Table of Contents
Table of Contents
PyroSim User Manual.ii
Table of Contents . iv
Figures. viii
Disclaimer. xi
Acknowledgements. xii
Chapter 1. Getting Started.1
Introduction .