Faculty of Engineering & Applied Science, UOIT
ENGR2230U: Statics
Assignment #2 November 22, 2010
Due Monday November 29 in class. This assignment is worth 5% of your final mark.
Late assignments are 25% off first day, 50% off second day and 100% off thir

University of Ontario Institute of Technology
Faculty of Engineering and Applied Science
ENGR 2430U
Dynamics
Assignment # 1
Instructor: Dr. H. Kishawy
Please answer the following questions:
12-6
12-11
12-15
12-17

University of Ontario Institute of Technology
ENGR 2430U: Dynamics
Assignment 4 (Due: March 12, 2012 at 4:00 pm)
Please, clearly write your name and student number on your solution sheet(s)
Q1. The 1.5Mg four-wheel-drive jeep is used to push two identical

University of Ontario Institute of Technology
Faculty of Engineering and Applied Science
MECE 2420U Fluid Mechanics
First Laboratory
Date performed: 21/01/2014
Date submitted: 04/01/2014
#
1
2
3
4
Name
Abdulaziz Hedaib
Hani Alahmadi
Adam
Sanket
ID
1004819

University of Ontario Institute of Technology
ENGR 2430U: Dynamics
Assignment 5 (Due: March 20, 2012 at 4:00 pm)
Please, clearly write your name and student number on your solution sheet(s)
Q1. The mechanism for a car window winder is shown in Fig. 1. Her

University of Ontario Institute of Technology
Faculty of Engineering and Applied Science
ENGR 2430U
Dynamics
Assignment # 2
Instructor: Dr. H. Kishawy
12-50,
12-70,
12-87,
12-91.

University of Ontario Institute of Technology
ENGR 2430U: Dynamics
Assignment 2 (Due: January 31, 2012 at 10:00pm)
Please, clearly write your name and student number on your solution sheet(s)
1
2

Fall 2016
Statics
MECE 2230U
Tutorial #8 with Solutions
Problem 1
Given: P1 = 200 lb, P2 = 500 lb
Find: The forces in each member of the truss.
Plan: First analyze pin B and then pin C
Solution to Problem 1
+ FX = 500 + FBC cos 45 (3/5) FBA = 0
200 lb
500

Assignment # 2
Instructor: Dr. Ghaus Rizvi
MANE 2220
Structure & Properties of Materials
Please show all your work to get marks for each part of the questions
Important instructions to follow (or else, you will lose marks!):
1
2
3
4
5
6
7
Answer questions

Assignment #1
Structure & Properties of Materials
MANE 2220
Instructor: Dr. Yasin hosseinkhani
Please show all your work to get marks for each part of the questions
Important instructions to follow (or else, you will lose marks!):
1
2
3
4
5
6
7
Answer que

Faculty of Engineering & Applied Science, UOIT
ENGR2230U: Statics
Assignment #1 October 2, 2010
Due Thursday October 14 in class. This assignment is worth 5% of your final mark.
Late assignments are 25% off first day, 50% off second day and 100% off third

ENGR2230 Statics: Lecture 01
MECHANICS, UNITS, NUMERICAL CALCULATIONS &
GENERAL PROCEDURE FOR ANALYSIS
Chapter 1 1.1 1.6
a) Explain mechanics / statics.
b) Review of Newtons Laws
c) Work with two types of measurement units.
d) Work with significant figure

University of Ontario Institute of Technology
ENGR 2430U: Dynamics
Assignment 6 (Due: March 27, 2012 at 4:00 pm)
Please, clearly write your name and student number on your solution sheet(s)
Q1. Determine the mass moment of inertia of the thin plate (Fig.