Session _
Multimedia Tutorials for Drawing Shear Force and Bending Moment Diagrams
Arnold Lumsdaine Department of Mechanical Aerospace and Bioengineering University of Tennessee 414 Dougherty Engineering Building Knoxville, TN 37996 phone: (865) 974-6650

Tuition Fees For New Students - 2008/2009 Per Semester
No. of Credit Hours
Undergraduate Egyptian (LE)
1st Level 2nd Level
Graduate International ($)
1st Level 2nd Level All Majors
Egyptian (LE)
MBA LLM
International ($)
Non-Degree (UG & G)
Egyptian (LE)

A2L05: Committee on Engineering Geology Chairman: John D. Duffy
Engineering Geology
JOHN D. DUFFY, California Department of Transportation JEFFREY R. KEATON, AGRA Earth & Environmental, Inc.
Engineering geologists are concerned with the distribution and r

How to Use Semilog Graph Paper
In semilog paper the C-axis is marked off so that the height represents the log of the value to be graphed. If you look at a semilog graph you'll notice that the horizontal lines are not drawn at even intervals, they start o

EXPERIMENT NO.1
Name of experiment:To determine the percentage of water for normal consistency for a given sample of cement Apparatus : Vicats apparatus with plunger of 10mm dia, measuring cylinder, weighing balance, weight box, , trowel. Theory : Standar

CIVL 3121
Shear Force and Bending Moment Diagrams for Frames
1/4
Shear and Moment Diagrams for Frames
A frame is a structure composed of several members that are either fixed or pin connected at their ends. It is often necessary to draw shear and moment d

Some Guidelines for Constructing Shear Force and Bending Moment Diagrams SIGN CONVENTIONS
+V +M +V +M
-M -V -V -M
BOUNDARY CONDITIONS
Ax A B Bx
Ay
Pinned LEFT End: Reaction force, Ax is unknown. Reaction force, Ay is unknown. V (shear force) = Ay (reactio

CIV 134 Theory of Structures A Extra Tutorial Questions Bending Moment and Shear Force
Question 1 A cantilever beam spans 6 metres, and supports a concentrated point load of 80 kN at 3 m from the encastr support as shown in Figure 1. Calculate the maximum

Graphing Rational Functions
A rational function is defined here as a function that is equal to a ratio of two polynomials p(x)/q(x) such that the degree of q(x) is at least 1. Examples: is a rational function since it is a ratio of two polynomials with de

STEEL-CONCRETE COMPOSITE COLUMN-I
25
STEEL-CONCRETE COMPOSITE COLUMNS-I
1.0 INTRODUCTION A steel-concrete composite column is a compression member, comprising either a concrete encased hot-rolled steel section or a concrete filled tubular section of hot-r

Chemically Testing for Water Quality
Lesson focus: water quality testing Lesson objectives:
Follow complex directions to complete chemical water tests to include ph, dissolved oxygen, phosphate, nitrate, alkalinity, or settable solids Record gathered dat

COMPARISON OF ISI AND ACI METHODS FOR ABSOLUTE VOLUME CONCRETE MIX DESIGN
Amarjit Singh, University of Hawaii at Manoa, USA Kamal Gautam, University of Hawaii at Manoa, USA
Abstract: The concrete mix design methods used in India and USA are built on the s

Female Figure Drawing Tutorial
Chest and Torso
I am going to begin this tutorial by addressing one of the most commonly asked questions that I receive: how to draw women's breasts (heh, I never thought I'd actually be making a tutorial about this. ^_^). O

Structural Analysis (I) Sheet No. (3)
Problems: 1- Two equal and opposite couples of magnitude M=25.0 kN.m are applied to the channelshaped beam AB. Observing that the couples causes the beam to bend in a horizontal plane, determine the stress: (a) at poi

Learning/Training Resources with Computer Aided Instructions in subject of
Projection of Points, Lines and Planes Planes Perpendicular to both the Referance Planes, Projection on Vertical Plane, Projection on Horizontal Plane, Planes Perpendicular to One

Department of Civil Engineering, The University of the West Indies, St. Augustine, Trinidad & Tobago
Course CE12B - CIVIL ENGINEERING DRAWING
Prepared by Dr. T.M. Lewis PREFACE Civil engineering drawing and structural detailing are concerned with translat

Theory of Structures
Mohrs circle for principle moment of inertia:
y v x u (Ix+Iy)/2 y u
x
Ix x
Ixy
v
u
Ixy
(Ix+Iy)/2
Ix > Iy & Ixy is positive
u Ix
x
Ix > Iy & Ixy is negative
Ixy
+ve u u
Ixy
-ve
y
y
(Ix+Iy)/2
Iy > Ix & Ixy is positive
(Ix+Iy)/2
Iy
Iy >

CIV 134 Theory of Structures A Unit 5
Definitions
Bending Moment:
Summary Sheet
Bending Moment and Shear Force
The bending moment at a section of a beam is the sum of the moments about that section of ALL the forces to the right or t o the left of the sec

Reading Section
Directions: These sample questions in the Reading section measure your ability to understand academic passages in English. You will read one passage and answer questions about it. In a real test, you would have 20 minutes to read the passa

From: "Saved by Windows Internet Explorer 8" Subject: =?windows-1256?B?3tPjIOXkz9PJIMfhyOTHwSDmx+HF5NTHwcfKIC0gx+HMx+PaySDH4Q=? = =?windows-1256?B?yt/k5uHmzO3J?= Date: Sat, 20 Mar 2010 19:19:02 +0200 MIME-Version: 1.0 Content-Type: multipart/related; type

Alibre Design - Drawing Tutorial 1
Alibre Design - Drawing Tutorial 1
Introduction
This tutorial guides you through the creation of your first Alibre Design drawing. You can quickly create drawings directly from parts and assemblies you have already model

2nd level Degree in Structural and Geotechnical Engineering Ph.D. course in Construction Engineering Course of Structural Assessment, Monitoring and Control
REBOUND HAMMER TESTING: CHARACTERISTICS AND OPERATIVE PROCEDURE
Eng. Mariacristina Spizzuoco
2nd l