ELG 3336 B
Lab 1- Inverting Operational Amplifier
Submitted to: Payman Rasekh
By
Stephanie Akpieyi - 7388695
Basmah Salami- 7869684
Introduction
Objective
The purpose of this experiment was to introdu
ELG3331: Lab1
Inverting Operational Amplifier
Objectives
To introduce operational amplifier circuits.
To illustrate the power supply regulation properties of operational amplifiers
Theory
The figure b
ELG3336
Design of Mechatronics System
Elements of a Data Acquisition System
2
Data Acquisition Hardware
Analog Signal
Your Signal
Data Acquisition System
DAQ Device
Computer
Computer
Cable
Terminal Bl
ELG3336
Lab. 1: Inverting Operational
Amplifier
TA: Mahfuz
[email protected]
10 September 2014
Objectives
The main objectives of this experiment are
To introduce operational amplifier (Op-Amp) circui
ELG3331: Design Problems for Instrumentations
Assignment Based on DAC, ADC and Comparators
Sections 15.4 and 15.5 of the textbook
Problem 1
Design an alarm system that is to be set off when room tempe
Introduction to MultiSim Part 1
Prepared by:
Mohamad Eid
Summer 2007
The purpose of this document is to introduce the many features of MultiSim. Begin by
first opening up MultiSim. For Windows users t
ELG3331: Tutorial on Chapter 10
Problem 10.6
See Figure 10.6 in the textbook. Assume the BJT has VBE = 0.7 V and = 150.
RB = R1 /R2 = 12.078 k
VBB =
IB =
R2
VCC = 3.5 V
R1 + R2
VBB - VBE
3 .5 0 .7
=
=
Physical Limitations of Op Amps
The IC Op-Amp comes so close to ideal performance
that it is useful to state the characteristics of an ideal
amplifier without regard to what is inside the package.
In
QUESTION I [5 marks):
Follow the procedure of solution, answer questions, identify mistakes (circle) and correct them, if
an !
Colisider the small-signal amplier shown in Figure 1; Assume Va; = 24 V.
ELG 3336 B
Lab 2- A BJT Common Emitter Amplifier
Submitted to: Payman Rasekh
By
Stephanie Akpieyi - 7388695
Basmah Salami- 7869684
Introduction
Objective
The objective of this experiment is to gain a
ELG3336 Midterm 1
Riadh Habash
Name:
Student Number:
1)
(a)
(b)
(c)
(d)
In designing an op-amp circuit for our project, the resistors should not exceed a value of what?
5 M
200 k
10 k
50
2) In design
ELG 3366
LAB 3- DIGITAL LOGIC CIRCUIT
AsharQureshi:8401491
MevilCrasta:8250420
TahaShahzad:8240272
OBJECTIVES
The objective of this lab was to become familiar with the basic logic operators. This was
University of Ottawa
Faculty of Engineering
ELG3336
Electric Circuits and Machines for Mechanical Engineers II
Lab 1 Report
GROUP MEMBERS
Ashar Qureshi: 8401491
Mevil Crasta: 8250420
Taha Shahzad:
ELG3336 B
Lab 3- Digital Logic Circuits
Submitted to: Payman Rasekh
By
Stephanie Akpieyi - 7388695
Basmah Salami- 7869684
Introduction
Objective
The objective of this lab is to design an OR gate using
Operational Amplifiers
Introduction of Operational Amplifier (Op-Amp)
Characteristics of an Op-Amp
Comparison of ideal and Non-ideal Op-Amp
Feedback and Non-Feedback
Configurations
Gain; Input Impedan
ELG 3336 Lab 3: Digital Logic Gates
Ysabelle So
7646041
1. Figure 1: AND gate using NOR gates
Input
A
0
0
1
1
B
0
1
0
1
Output
Z = (A+B)
1
0
0
0
B
0
1
0
1
Output
Z = (AB)
1
1
1
0
2. Figure 2: OR gate
ELG3331
Lab 2: A BJT Common Emitter Amplifier
Objective: To understand the operation of BJT and common-emitter amplifier.
Theory: Study Section 10.2 of the textbook.
Equipment and Components:
2N3904
ELG3331: Digital Tachometer
Introduction to Mechatronics by DG Alciatore and M B Histand
Our objective is to design a system to measure and display the rotational
speed of a shaft. A simple method to
ELG3336: Op Amp-based Active Filters
Advantages:
Reduced size and weight, and therefore parasitics.
Increased reliability and improved performance.
Simpler design than for passive filters and can
Digital Systems
Based on Principles and Applications of Electrical Engineering/Rizzoni (McGraw Hill
Objectives:
Analyze the operation of sequential logic circuits.
Understand the operation of digital
Bipolar Junction Transistors (BJT)
Signal amplification is important in many applications, such
as telecommunications. Before the advent of transistors,
signal amplification was accomplished using vac
ELG3331: An OP AMP Circuit used for Measuring the Change in
Strain Gage Resistance
(Electric Circuits: Nillson and Riedel)
Changes in the shape of elastic solids are of great importance to engineers w
ELG3331: DESIGN OF LOGIC CIRCUIT
Suppose we intend to design a remote door lock which is operated by an electrical relay that requires 15
mA to operate. The relay may be opened by two switches A or B
ELG3336: Converters
Analog to Digital Converters (ADCs)
Digital to Analog Converters (DACs)
Digital Output Dout
111
110
101
100
VFSR
V, VLSB
011
010
001
000
Vref
8
4
Vref
8
7
Vref
8
Analog Input Vin
A
Digital Logic Circuits
Digital describes any system based on discontinuous data
or events. Typically digital is computer data or electronic
sampling of an analog signal. Computers are digital
machine