Routing Protocols and Concepts
CCNA Exploration 2: Chapter 7 toets antwoorden / CCNA Routing Protocols
and Concepts exam 7 answers
CCNA Exploration 2: Routing Protocols and Concepts Chapter 7 Exam Answers
1. What field was added to the
Refer to the exhibit. Which command should be used to configure EIGRP to only advertise the network that is
attached to the gigabit Ethernet 0/1 interface?
network 172.16.23.64 0.0.0.63
network 172.16.23.0 255.255.255.192
1. Why do OSPF serial interfaces usually require manual bandwidth configuration?
OSPF uses the bandwidth value to compute routes for its routing table.
Each side of an OSPF serial link should be configured with a unique value.
All serial inter
1. Refer to the exhibit. What three conclusions can be drawn from the displayed output? (Choose three.)
The DR can be reached through the GigabitEthernet 0/0 interface.
This interface is using the default priority.
The BDR has three neighbo
What features are found in EIGRP
that are not found in other distance
vector routing protocols?
What type of protocol does EIGRP
What type of routing protocol is
How is EIGRP similar to RIP v2?
Reliable Transport Protocol (RTP)
Module OSPF Practice Test Answers
Two neighbouring routers are configured for OSPF, but they have different hello and dead
intervals. What will happen?
They will become adjacent as long as they are configured for the same area.
They will negotiate a hello
The exhibit displays this information:
Router R1 serial 0/0/1 has an IP address of 192.168.10.9 /30 and is connected to serial 0/0/0 on router R3 with
an IP address of 192.168.10.10 /30.
Router R2 serial 0/0/1 has an IP address of 192.168.10.5 /30 and is
CNET311 Routing and Switching
Which two features of enterprise class equipment assists an enterprise network in maintaining 99.999 percent
up-time? (Choose two.)
redundant power supplies
The trunk link between two 2960 switches has reached its capacity. How can this be addressed in the most
Increase the speed of the ports.
Decrease the size of the inter-switch collision domain by configuring additional VLANs.
CCNA Exploration 2: Chapter 9 toets antwoorden / CCNA Routing Protocols
and Concepts exam 9 answers
CCNA Exploration 2: Routing Protocols and Concepts Chapter 9 Exam Answers
1. By default, which two metrics are used by EIGRP to determine the best path bet
CCNA Exploration 2: Chapter 10 toets antwoorden / CCNA Routing Protocols
and Concepts exam 10 answers
CCNA Exploration 2: Routing Protocols and Concepts Chapter 10 Exam Answers
1. What are some of the advantages of using a link-state routing protocol inst
Convocation Invitation and Guest Tickets
May 31, 2016
9 Lionhead Trail
Student Number: 300813795
Congratulations! You have successfully completed all of your program requirements and we invite you
CNET311 Lab-Analyze Frames in LAN
Run Wireshark Network Analyzer, capture random traffic flows for about 30 seconds. Analyze
the captured data and answer the following:
1). Which of the following protocol PDUs (messages) have been captured?
IP, TCP, UDP,
School of Engineering Technology
and Applied Science
Information and Communication
Computer Systems Technician
Computer Systems Technology
CCNA3 Chapter 3 Practice Test Answers
The network shown in the diagram has just been configured and none of the
switches yet has any entries in its bridging table. Workstation A1 sends out a
Routing and Switching
Refer to the exhibit. The network administrator has just added VLAN 50 to Switch1 and Switch2
and assigned hosts on the IP addresses of the VLAN in the 10.1.50.0/24 subnet range. Computer
A can communicate with com
Collection of workstations and servers on a LAN that are designed to communication and
exchange data with one another.
Program that performs a function directly for a user.
What are some network applications?
FTP and Telnet Clients
Routing and Switching
1. Which layer of the hierarchical network design model is referred to as the high-speed
backbone of the internetwork, where high availability and redundancy are critical?
Routing and Switching
1. Which three actions might a Frame Relay switch perform when it detects an excessive buildup of frames in its queue? (Choose three.)
puts a hold on accepting frames in excess of the CIR
drops frames from the queu
CCNA3 Chapter 1 Practice Test Answers
At which layer of the hierarchical network design would you find switches that
use access control lists to implement security?
All 3 layers
At which layer of the hierarchical network design wo
CCNA3 Chapter 2 Practice Test Answers
An Ethernet network is using CSMA/CD and a collision has occurred. Which
host will be the next to transmit data?
The host that was the first to detect the collision.
The host that was the first to transmit data that w
CCNA3 Chapter 4 Practice Test Answers
What is the default Catalyst switch configuration?
VTP version 1, Mode server, Domain name cisco1, revision number 1.
VTP version 1, Mode server, no Domain name, revision number 0.
VTP version 2, Mode server, no Domai
Ch02 - LAN Redundancy
What could be the effect of duplicate unicast frames arriving at a destination device due to multiple active
alternative physical paths?
Frame collisions increase.
The number of broadcast domains increases.