Mechanics of Deformable Bodies
Due: Tuesday, November 24th, 2015
1. (40 points) For each of the following statically determinate beams, EI is constant along the length of the
Clearly state the boundary conditions on the displacement, sl
A-PDF Split DEMO : Purchase from www.A-PDF.com SECTION 2.10 Stresswatermark to remove the Concentrations
Problem 2.10-7 A stepped bar with a hole (see figure) has widths b 2.4 in. and c 1.6 in. The fillets have radii equal to 0.2 in. What is the diameter
COE 3001 - Deformable bodies
An aluminum (E=10600 ksi) wire of diameter d=1/10 in and length L=I2 ft is subjected to
tensile load P. Find the maximum allowable load if the allowable stress is 10 ksi. and the
COE 3001 DefBods: Test #1 Sept 22, 2009
(80 minutes, closed books, calculator and
one sheet of formulae allowed)
(30 points) A bar AB of length L is held between rigid
supports and heated nonuniformly in such
a manner that the temperature increas
A-PDF Axially Loaded : Purchase CHAPTER 2 Split DEMOMembers
from www.A-PDF.com to remove the watermark
Problem 2.5-8 A brass sleeve S is fitted over a steel bolt B (see figure), and the nut is tightened until it is just snug. The bolt has a diameter d
1. A high-strength steel bar used in a large crane has diameter d=1.00 in. The
steel has modulus of elasticity E=29x106 psi and Poissons ratio v=0.29. Because
of clearance requirements, the diameter of the bar is limited to 1.001 in wh
Normal Stress and Strain
Problem 1.2-1 A solid circular post ABC (see figure) supports
a load P1 2500 lb acting at the top. A second load P2 is
uniformly distributed around the shelf at B. The diameters of
Idealized Buckling Models
Problem 11.2-1 through 11.2-4 The figure shows an idealized structure
consisting of one or more rigid bars with pinned connections and linearly
elastic springs. Rotational stiffness is denoted R and tra
GEORGIA INSTITUTE OF TECHNOLOGY
COE 3001-G DEFORMABLE BODIES, Spring 2016
Lectures: MW 4:35-5:55 at Mason 1133
Office hours: Tuesday 3-4 pm and Friday 1-2 pm at Love building ro
COE 3001 — Test 1 — Spring 2013
Name (PLEASE PRINT): K6]
Show all work.
Pictures are NOT drawn to scale.
If you make an assumption, state it clearly.
Use the back of the equation sheet as scrap paper if needed.
Define clearly any new variable
COE 3001 - Test 2 - Spring 2013
Name (PLEASE PRINT): KEV
1. Show all work.
2. Provide units on answers.
3. Pictures are NOT drawn to scale.
4. If you make an assumption, state it clearly.
5. Use the back of the equation sheet as scrap paper i
Mechanics of Deformable Bodies, Section Q
Friday, April 4, 2014
The following test is 6 pages long with 4 questions.
One double-sided equation page is permitted. Scientific calculators are allowed.
This test is out of 100 possible points.
4% b) 1 8%
U H. Way, Mayo
Pg mfsyso Mil/3 '10
f), f 4 - \
. Wit/135 VCC/ZB
(at?) WW3 -: M (be)
Em). VLF/4;) : VECL/p) [sw
' % M +29; c 11%,
n 3% -(%)(<D+%LD
g. 3 % RA 3 3%"
V597 gg/L/g "V X W7]
roux/g x 7 L/L
my WWW; Wa
g, 7/ 3.