EEM1016 ENGINEERING MATHEMATICS 1
TRIMESTER 1, 2016/2017
BIG EXERCISES CHAPTER 1 WEEK 3 DIFFERENTIATION
1) Find the derivatives using differentiation rules.
a) y 2 x 2 5 2 x 3
c) z 4 t 1 t 2
3 x 2 5x 4
11. Solid Editing
There are two options associated : circular and elliptical.
This means that cones can be drawn with either an
elliptical or circular base plane.
A torus is a donut like shape
Create 3D Wall like Solid
5. SECTIONAL VIEWS
Sectional views are used in technical drawing to expose internal surfaces.
Do not contain hidden lines, include all lines that are directly visible. .
Hatch lines are drawn on the surfaces that represent where the cutting
EME 2066 Measurement and Instrumentation
Measurement of fluid flow is important ranging from measurements of blood flow
rates to the measurement of the flow of liquid oxygen in rocket.
There are different flow m
EEM 1016 Engineering Mathematics 1: Partial Derivatives
Chapter 4: Partial Differentiation
Previously we have studied functions of one variable, y = f(x). We are going to expand
the idea of functions to include functions with more than one independent var
10. Fundamental 3D Modeling
WORLD COORDINATE SYSTEM (WCS)
coordinate system is called
the world coordinate
The default setting for the
WCS is a viewing position
located so that you are
looking at the system 90to
its X,Y p
STUDIO 04A: Sectional Views
1. DIMENSION in mm. Construct the top view and sectional view A-A.
2. DIMENSION in mm.
3. DIMENSION in inch. Construct the front view and sectional view A-A.
4. DIMENSION in inch. Redraw the given view, and add the specific sec
& GEOMETRIC TOLERANCES
DIRECT TOLERANCE METHODS
A bilateral tolerance has both a plus and a minus value. A
unilateral tolerance has either the plus or minus value
equal to 0
Zero limit for inch values must include
Infineon Week 2017
Advances in Semiconductor Packaging & Test Technology
Innovative Semiconductor Solutions for Energy Efficiency, Mobility and
Jointly organized by Multimedia University and Infineon Technologies (M) Sdn Bhd
28 April 2017
Blocks are groups of entities saved as a single unit. Blocks
are used to save shapes and groups of shapes that are
used frequently when creating drawings.
Once created, blocks can be inserted into the drawings,
thereby saving drawing ti
A Loschmidt apparatus is constructed with L = 50cm. Benzene is placed in the lower tube and air in
the upper tube at 1 atm (standard pressure) and 25oC. The mole fraction of Benzene after 10min
after the connection is opened is 0.928 in the lower tube. Wh
FACULTY OF ENGINEERING AND TECHNOLOGY
FET Lab Report Submission Cover Page
Section A Filled Up By Student
Academic Year : Beta / Gamma / Delta / Epsilon
Subject Code & Name: _
Workstation No : _
Project P3.8 Ultimate Load of a Beam Under Pure Bending
Bending of beams is a frequently encountered loading situation in practice. A slender member
subject to traverse loads is termed as a beam under bending. At any cross-section, the traverse
EME1046 Principles of Thermodynamics
Tri 1, 2014/15
Tutorial 1a: Introduction and Fundamental Concepts
1. (a) Convert 223C into K.
(b) Convert 1.31 bar into kN/m2.
(c) Convert 4250 Pa into atm.
(d) Convert 1 kgf/cm2 into psi.
2. (a) A vacuum gage connec
EME 2066 Measurement and Instrumentation, Trim.3, 2015-2016
*To be worked out by tutor in Tutorial class.
The remaining problems are to be worked out by students in tutorial
hours for submission (individually, hand written only) at the end of
EME2066 Tutorial #3 (3 2015/2016)
1. Convert the following gage pressure readings to kPa assuming that atmospheric pressure is
760 mm of Hg.
80 cm of Hg
(ii) 30 cm of Hg
(iii) 1.35 m H O
(iv) 4.2 bar
2. On a piston of 10 cm diameter a force of 1000 N
A. SUBJECT INFORMATION
Name of Subject/Module
Name of Subject Coordinator
Measurement and Instrumentation
B. LIST OF TEACHING STAFF CONTACT DETAILS:
Min Thu Soe
EME 2066 Measurement and Instrumentation- Trim.3, 2015-2016
BASIC ELECTRICAL MEASUREMENT AND SENSING DEVICES
*To be worked out by tutor in Tutorial class.
The remaining problems are to be worked out by students in tutorial hours for submission
Fundamental of 2D Construction
The Line command is
used to draw straight
two defined points
The Line tool on
the Draw panel
To randomly select points
Command: _line Specify first
2. Place the cursor ra
FACULTY OF ENGINEERING & TECHNOLOGY
STRENGTH OF MATERIALS
TRIMESTER 2 (2016/2017)
Torsion of Round Wire and Bar
Note: Students are advised to read through this lab sheet before doing experiment.
Introduction to AutoCAD
1. Recommend use official email @mmu.edu.my
3. Valid for 3years
To start a new drawing
Select template dialog box
Page Setup Manager
Page Setup Manager
COMPUTATIONAL METHODS FOR MECHANICAL ENGINEERING
Question 1 (Final exam, 2007)
T = 100qC
T = 50qC
Figure 1.1 shows a bar with non-insulating side surface. The governing equation of the
system is given in equatio
Dear Dean of Faculty of Engineering and Technology
I am writing this letter to appeal baring decision for EEM1026 Engineering Mathematics Two. I believe
that I deserve to write my final exam for several reasons.
My Family health issues that prevented me t
In Malaysia, the government plays three major roles in the
employment system. This is provided in the Ninth Schedule of
the Federal Constitution i.e. employment matter is a federal
and not state matter.
APPLICATION OF MONEYTIME RELATIONSHIP
MINIMUM ATTRACTIVE RATE OF
RETURN ( MARR )
An interest rate used to convert cash flows
into equivalent worth at some point(s) in time
Usually a policy issue based on:
amount, source and cost of money
Most engineering projects can be
accomplished by more than one feasible
Two rules are used in selecting alternatives:
1. When revenues and other economic
benefits are present,
INTELLECTUAL PROPERTY LAW
Introduction to Intellectual Property
Layout Design of Integrated Circuit
IP rights are the rights given to the persons
over the creat
EME 3056 Industrial Management
Engineering Economy Tutorial 2: Money-Time Relationship
Based on the following loan information,
Loan Principle = $10,000
Interest Rate = 8% per yearly
Duration of Loan = 3 years
Annual Payment = $3,880
F O U N D AT I O N S O F E N G I N E E R I N G E C O N O M Y
Introduction to engineering economy.
Non-linear breakeven analysis.
The material in these notes are adapted
6.1 Pressure Wave Propagation in Rigid Pipe
The bulk modulus of liquid (isentropic and isothermal) are defined as
is commonly used and therefore the bulk modulus