6.3. Selection of the balls.
The standard ball set contains 6 balls, which pass through the measuring tube of
an inner diameter of approximately 15.94 :I:0.01 mm.
Density Ball Measuring
' '. p glam3 diameter mPa 5 range mPa's
mm. 5"
a rox.
.
Glass
Boro
6/5/2016
Fluid Mechanics
(ENGI1168)
Chapter 1. General Introduction
Australian College of Kuwait
What is Fluid Mechanics?
Fluid Mechanics is concerned with the behavior
of fluids at rest and in motion.
The branch of fluid mechanics that deals with
the b
Homework # 1
Australian College of Kuwait
School of Engineering
Petroleum Engineering Department
Fluid Mechanics
151PTE324 and ENGI1168
Due Date: Thursday, June 16, 2016 in Class (1:30 PM to 4:00 PM)
Problem 1  A mass of a fluid of 425 kg occupies exactl
6/5/2016
Fluid Mechanics
(ENGI1168)
Chapter 5. Control Volume Approach
and Continuity Equation
Australian College of Kuwait
Discharge (Flow Rate)
1
6/5/2016
Discharge (Flow Rate)
Discharge (Flow Rate)
2
6/5/2016
Mass Flow Rate
Example
3
6/5/2016
Control V
6/5/2016
Fluid Mechanics
(ENGI1168)
Chapter 4. Fluid Dynamics
Flowing Fluid and Pressure Variation
Australian College of Kuwait
Streamlines
1
6/5/2016
Streamlines
Streamlines
2
6/5/2016
Types of Flows
Uniform and Nonuniform Flows
Types of Flows
Steady and
6/5/2016
Fluid Mechanics
(ENGI1168)
Chapter 7. Momentum Equation
Australian College of Kuwait
Force Equation
1
6/5/2016
Momentum Equation
Momentum Equation
2
6/5/2016
Vanes
Nozzles
3
6/5/2016
Nozzles
Example
4
6/5/2016
Example
Example
5
6/5/2016
Example
E
6/5/2016
Fluid Mechanics
(ENGI1168)
Chapter 6. The Energy Equations
Australian College of Kuwait
General Definitions
1
6/5/2016
General Definitions
Introduction
2
6/5/2016
Pumps
Pumps
3
6/5/2016
Turbines
Turbines
4
6/5/2016
Fluid Friction
Head loss in pip
Fluid Mechanics ENEM12006
Experiment three: flow measurements
1. Objectives:
Several types of flow meters will be studied for their characteristics including accuracy and head
loss. Calibration of a flow meter will also be performed.
2. Equipment:
3. Proc
6/5/2016
Fluid Mechanics
(ENGI1168)
Chapter 8. Flow in Pipes
Australian College of Kuwait
Introduction
1
6/5/2016
Introduction
Introduction
2
6/5/2016
Introduction
Visualizing Laminar Flow in a Circular
Pipe
3
6/5/2016
Visualizing Laminar and Turbulent
Fl
6/5/2016
Fluid Mechanics
(ENGI1168)
Chapter 2. Properties of Fluids
Australian College of Kuwait
Density and Specific Weight
1
6/5/2016
Density of Water and Gravitational
Acceleration
EE
(g/cm3)
Water Density Variation with
Temperature and Pressure
(C)
2
6/5/2016
Fluid Mechanics
(ENGI1168)
Chapter 3. Fluid Statics
Australian College of Kuwait
Fluid Pressure
1
6/5/2016
Absolute Pressure
Gage and Vacuum Pressure
2
6/5/2016
Gage and Vacuum Pressure
Gage and Vacuum Pressure
3
6/5/2016
Example
Pressure at a Po
Fluid Mechanics ENEM12006
Experiment five: Bernoullis principle
1. Objectives:
The Objectives from this experiment is:

To verify experimentally the validity of Bernoullis equation for fluid flow .
Pressure measurements along Venturi nozzle
2. Equipment:
Fluid Mechanics ENEM12006
Experiment four: Reynolds Number
1. Objectives:
The Objectives from this experiment is to study the transition between laminar and turbulent
flow.
2. Equipment:
3. Procedure:
1.
2.
3.
4.
5.
Connect the H215 Reynolds No and Transl
Homework # 3
Australian College of Kuwait
School of Engineering
Petroleum Engineering Department
Fluid Mechanics
151PTE324 and ENGI1168
Due Date: Tuesday, June 28, 2016 in Class (3:30 to 6 PM)
Problem 1 The nozzle in the figure is shaped such that the vel
Fluid Mechanics ENEM12006
Experiment two: Viscosity Measurements
1. Objectives:
The purpose of this lab is to determine the viscosities of two different oil samples using a falling ball
viscometer
2. Equipment:
Figure 1: VISCO BALL
3. Theory:
A falling ba
Homework # 2
Australian College of Kuwait
School of Engineering
Petroleum Engineering Department
Fluid Mechanics
151PTE324 and ENGI1168
Due Date: Saturday, June 25, 2016 in Class (12:30 PM to 3:00 PM)
Problem 1 What is the pressure at the center of pipe B
Fluid Mechanics ENEM12006
Experiment one: Flow Rate
1. Objectives:
To measure flow rates using the volume time method and to estimate the accuracy and precision of
the collected data.
2. Equipment:
Figure 1: Hydraulic Bench
3. Procedure:
1. Turn on the pu