SWC 211 Soil and Water Conservation Engineering
DUMPY LEVEL
HEIGHT OF COLLIMATION AND RISE & FALL METHOD
Aim:
To determine to difference in elevation between the given points adopting height
of collim
SWC 211 Soil and Water Conservation Engineering
COMPASS SURVEY
RADIATION AND INTERSECTION METHOD
Aim:
To determine the area of the given field by radiation and intersection method
using a prismatic co
SWC 211 Soil and Water Conservation Engineering
CHAIN AND CROSS STAFF SURVEY
Aim:
To locate the boundaries of a given field and also to determine the area.
Instruments required:
Chain, Cross staff, Ar
SWC 211 Soil and Water Conservation Engineering
STUDY AND USE OF SURVEYING AND LEVELING INSTRUMENTS
Surveying is defines as the art of determining the relative positions of various
points above, on or
SWC 211 Soil and Water Conservation Engineering
PLANE TABLE SURVEY
General:
In case of plane table survey, the measurements of survey lines of the traverse and
their plotting to a suitable scale are d
AUTOMOBILE ENGINEERING
th
8 SEMESTER
MECHANICAL ENGINEERING
MODULE-I
INTRODUCTION
MODULE-II
CLUTCH
GEARS
BRAKING SYSTEM
MODULE-III
STEERING GEOMETRY AND FRONT AXLE
SUSPENSION SYSTEM
ELECTRICAL SYSTEM
ISSN: 2319-8753
International Journal of Innovative Research in Science, Engineering and Technology
Vol. 2, Issue 5, May 2013
DESIGN OF TOGGLE JACK CONSIDERING
MATERIAL SELECTION OF SCERW - NUT
COMBIN
SUB:- MCHINE DESIGN-I MODULE-II (DESIGN OF JOINTS) Riveted Joint Often small machine components
are joined together to form a larger machine part. Design of joints is as important as that of machine
c
Advanced Design of steel and Composite
structures
INTRODUCTION TO FATIGUE
Professor Dan Dubina
Introduction to fatigue
EN 1993 Framerwork
Introduction to Fatigue
Fatigue may occur when a member is su
Shear Center with Examples
What happens when loads act in a plane that is not a plane of symmetry?
-Loads must be applied at particular point in the cross section, called shear center, if the beam is
1
SUB:- MCHINE DESIGN-I (BME 310)
MODULE-II (DESIGN OF JOINTS)
Often small machine components are joined together to form a larger machine part.
Design of joints is as important as that of machine com
1 LECTURE NOTES SUB:- MCHINE DESIGN-I (BME 310) MODULE-II (DESIGN OF JOINTS) Riveted Joint
Often small machine components are joined together to form a larger machine part. Design of joints is as
impo
Design of Steel Structures
Prof. S.R.Satish Kumar and Prof. A.R.Santha Kumar
1.7 Fatigue of steel structures
A component or structure, which is designed to carry a single monotonically
increasing appl
ENEL804 Sustainable Energy Systems Homework 1 Semester 1
Due: Tuesday, 14 March 2017
Niranjan Patil
16924914
1. What is Distributed Generation? Explain briefly the important features of
Distributed Ge
Project on :- raymond -values
Presented By:
Suraj Sanjay Jadhav
Roll no. 19
MBA Part 1
University Depatment,
Shivaji university,
kolhapur.
Under the Guidence:
Dr. H.M.Thakar Sir
Address: Plot No. T-1,
Study of Segmentation, Targeting,
Differentiation
and Positioning of a Prestigious car
Mercedes Benz
From: Vaibhavi Todankar, Roll no.: 34, MBA PART-1.
Marketing Segmentation
The Key to Profitability
Table A: Annual K2-Tape Sales (in Millions)
2008
2009
2010
2011
$39.6
$44.4
$49.9
$57.5
2012
$68.6
Table B: K2-Tape Case Sales by Grade
July - December 2011 Case Sales
January - June 2012 Case Sales
G
Exhibit 1: Wilkerson company operating results
Sales
Direct labour
Direct material
Manufacturing overhead
Machine related (Dep/Maint)
Set up labour
Receiving and production control
Packaging and Shipp
Exhibit 1: Wilkerson company operating results
Sales
Direct labour
Direct material
Manufacturing overhead
Machine related (Dep/Maint)
Set up labour
Receiving and production control
Packaging and Shipp
Instructions
This Spreadsheet contains the Exhibits from the Mountain Man Case Study and an interactive forecasting model
which allows users to evaluate the effects of launching the MM Light Product.
A stem and leaf diagram provides a visual summary of your data and allows to detect
distribution pattern of the data.
To draw the stem and leaf diagram, we split the data in STEM and LEAVES then we
ar
This assignment requires you to use Excel; make sure you also submit the Excel file to
show your work. Place all calculations for each of the questions on a separate
worksheet. Then, using the results
Question 20:
Solution: We are given that , scores of 10 students. We have to find percentile of score 11.
Data is : 20,8,10,7,15,16,12,19,14,9
Arrange the data in ascending order.
7,8,9,10,12,14,15,16
Question 16:
Solution: We are given that , high temperature in a certain city for the month of August follow a
uniform distribution over the interval 65 0 and 850. We have to find the
P( high temp bet
Question 15:
Solution:
a)
We have to find regression equation y = b0 + b1x for given data.
We have to find : b0 and b1
x
Y
x2
x*y
1
3
4
6
0
x =14
3
7
9
13
3
y = 35
1
9
16
36
0
2
x = 62
3
21
36
78
0