View the step-by-step solution to:

Audio Amplifier Project This is a group project which will require working with another student. The project is a design project using Multisim with...

Final project. I really need assistance on this. I would like to start at $20 and depending on how much answer you provide ill tip more. So if you do the whole project ill pay up to $50, but if you just want to provide screen shots and steps then we can decide on something else. Are you ok with this?

Audio Amplifer Project This is a group project which will require working with another student. The project is a design project using Multisim with the requirements given below. The project is due on the last day oF the term. Total Points: 100 Project name: Audio Amplifer (Multistage) Audio Amplifer Power Output selection: 3.2 W, 5.6 W, 7.1 W, 8.4 W, 11.5 W, and 16.3 W Audio Amplifer Input Voltage (peak) selection: 150mV peak , 200mV peak , 250mV peak Audio Frequency: 20 Hz – 20 KHz Deliverable: Multisim design (soFt copy), test results, short report, and teamwork evaluation Project Defnition: Design, simulate, and test an Audio Amplifer which delivers one oF the above power outputs to an 8Ω speaker load. The output power oF your design and the input signal oF your design must be selected From the above list. The audio Frequency range is between 20 Hz to 20 KHz, so the operating Frequency oF your design will be within this range. The measuring equipment should display the output power and the input signal oF your design. You are required to use either or both NPN and PNP transistors, but not an op-amp. It is recommended that you use multistage amplifcation oF any class amplifers oF your choice. You should try to minimize your usage oF components and be cost e±ective. Project Structure: In general, you will have one other classmate in your team. Each oF you will design and simulate an audio amplifer with di±erent specifcations, each making your choice From the above parameters. Thus, it is highly suggested that you
Background image of page 1
communicate with your partner as early as possible to plan and coordinate your activities, select the input voltage and output power for your design, and establish a schedule. For the testing phase, you will develop a test plan and characterize and validate your teammate’s ampli±er. During the project period, you are encouraged to communicate, exchange ideas, and help each other complete your project. A team area will be set up for you in Blackboard, and you are required to use this area as part of your grade will be based on e²ectively using this tool. Project Deliverable: Report and the multisim design for your project Each student will submit an individual report. The report should, as a minimum, include the following: Title Page (Name, Partners name, like the table they have in the document) Description of your project (including the speci±cations you selected) Design methodology (show calculations and provide rationale for design choices; remember that your choices must take into consideration commonly available parts) Final schematic in Multisim Components/Parts list with cost and total project cost Simulation results for your design Testing process and results for characterization and validation of your teammate’s design – screenshots along will not su³ce. Description of process is required along with discussion of results. Project Challenges: Note any di³culties you faced during the completion of your design and how you overcame them Team Interaction Re´ection: Describe how you used Blackboard to facilitate interaction, how you worked with one another in the design phase, challenges you encountered, methods you employed to overcome any challenges. Teammate Assessment: Use the Project Participation Rubric below and give your teammate a ranking of Needs Improvement, Competent, or Excellent for the ±rst two items in the rubric: Interacts professionally and Plans and organizes team e²ort. Be sure to justify your ranking. Conclusion
Background image of page 2
Show entire document
Sign up to view the entire interaction

Top Answer

Please see the attached... View the full answer

5.6W and 8.4 W.zip - Preview not available

Sign up to view the full answer

Why Join Course Hero?

Course Hero has all the homework and study help you need to succeed! We’ve got course-specific notes, study guides, and practice tests along with expert tutors.

-

Educational Resources
  • -

    Study Documents

    Find the best study resources around, tagged to your specific courses. Share your own to gain free Course Hero access.

    Browse Documents
  • -

    Question & Answers

    Get one-on-one homework help from our expert tutors—available online 24/7. Ask your own questions or browse existing Q&A threads. Satisfaction guaranteed!

    Ask a Question
Ask a homework question - tutors are online