Solved by Expert Tutors
Solved by Expert Tutors
Question

# Question 1: Multi-view Drawing

Consider the slide shown in Figure 1 below
a) Model (create) the part (.prt) in Creo Parametric and name it Lastname_Final_Q1. b) Create a drawing file (.drw), showing the necessary views and the isometric view, assuming that the surfaces shown are front, top, and right side (Be sure to include all center lines)
c) Adjust the scale, if necessary, to cover at least 80 % of the available drawing area d) Insert an A format and fill in the title block
e) Dimension f) From the drawing file, create a PDF file (.pdf)
g) Submit the part file at Final_Part_1, the drawing file at Final_Drawing_1, and the PDF file at Final_PDF_1 assignments in Moodle
Question 2: Auxiliary view Drawing
Consider the Plastic Slide shown in Figure 4 (Exercise 7.5 on page 297 of the textbook) a) Model (create) the part in Creo Parametric and name it Lastname_Final_Q2.
b) Create a drawing file (.drw) showing the necessary views, the isometric view, and one auxiliary view, assuming that front, top, and right side surfaces are shown. (Be sure to include all center lines) c) Adjust the scale, if necessary, to occupy at least 80 % of the available drawing area
d) Insert an A format and fill in the title block e) Dimension
f) Create a PDF file ( .pdf) from the drawing file (drw) g) Submit the part file at Final_Part_2, the drawing file at Final_Drawing_2, and the PDF file at Final_PDF_2 in Moodle

Figure 2
Question 3: Sectional-view Drawing Download the Centering Bushing shown (Exercise 6.9 on page 245 of the textbook) from Moodle under Week 5
a) Create a drawing showing the necessary views and the isometric view, assuming that front, top, and right side surfaces are shown b) Adjust the scale, if necessary, to occupy at least 80 % of the available drawing area
c) Convert the right-side view into a full section view. The cutting plane passes through the center of the lower hole and is perpendicular to the front surface d) Insert an A format
e) Do NOT dimension f) Create a PDF file from the ProE drawing file
g) Submit the drawing file to Final_Darwing_3 and the PDF file at Final_PDF_3 in Moodle

ECPI UNIVERSITY School of Engineering Technology Electronics Engineering Technology Department EET 192 Final Exam Question 1: Multi-view Drawing Consider the slide shown in Figure 1 below a) Model (create) the part (.prt) in Creo Parametric and name it Lastname_Final_Q1. b) Create a drawing file (.drw), showing the necessary views and the isometric view, assuming that the surfaces shown are front, top, and right side ( Be sure to include all center lines ) c) Adjust the scale, if necessary, to cover at least 80 % of the available drawing area d) Insert an A format and fill in the title block e) Dimension f) From the drawing file, create a PDF file (.pdf) g) Submit the part file at Final_Part_1, the drawing file at Final_Drawing_1, and the PDF file at Final_PDF_1 assignments in Moodle Figure 1 Question 2: Auxiliary view Drawing Consider the Plastic Slide shown in Figure 4 (Exercise 7.5 on page 297 of the textbook) a) Model (create) the par t in Creo Parametric and name it Lastname_Final_Q2.
ECPI UNIVERSITY School of Engineering Technology Electronics Engineering Technology Department b) Create a drawing file (.drw) showing the necessary views, the isometric view, and one auxiliary view, assuming that front, top, and right side surfaces are shown. ( Be sure to include all center lines ) c) Adjust the scale, if necessary, to occupy at least 80 % of the available drawing area d) Insert an A format and fill in the title block e) Dimension f) Create a PDF file ( .pdf) from the drawing file (drw) g) Submit the part file at Final_Part_2, the drawing file at Final_Drawing_2, and the PDF file at Final_PDF_2 in Moodle Figure 2 Question 3: Sectional-view Drawing Download the Centering Bushing shown (Exercise 6.9 on page 245 of the textbook) from Moodle under Week 5
Show entire document

fficitur laoreet. Nam risus ante, dapibus a

ipsum dolor sit amet, consectetur adipiscing elit. Nam lacinia pulvinar tortor nec facilisis. Pellentesque dapibus efficitur laoreet. Nam risus ante, dapibus a molestie consequat, ultrices ac magna. Fusce dui lectus, congue vel laoreet ac, dictum vitae odio. Donec aliquet. Lorem ipsum d

at, ultrices ac magna. Fusce dui lectus, congue vel laoree sum dolor s c sum dol c llentes c tesque c ec aliquet c sque dapib c sum dolor sit amet, consectetur adipiscing c ec aliquet. Lore c Fusc

### Why Join Course Hero?

Course Hero has all the homework and study help you need to succeed! We’ve got course-specific notes, study guides, and practice tests along with expert tutors.

• ### -

Study Documents

Find the best study resources around, tagged to your specific courses. Share your own to gain free Course Hero access.

Browse Documents