. Addressing and Routing In this assignment, you must create the...

Image transcription text

Addressing and Routing In this assignment, you must create the addressing scheme of a Local Area Network (LAN) using the range 192.168.10/24, apply your addressing scheme to the interfaces of the computers and routers and configure routing between routers so all computers can be reached from any point in the entire network. Your scheme must take into account the following parameters: You must create one separate subnet for each of the following groups. Marketing with 80 users Accounting with 20 users Server blocks with 15 servers 4 Segments for the backbone links between the routers Write down your results in the table below. Network ist address Last Address Subnet Mask Default Gateway Marketing Address Address Address Address Accounting Address Address Address Address Server block Address Address Address Address Backbone 1 Address Address Address None Backbone 2 Address Address Address None Backbone 3 Address Address Address None Backbone 4 Address Address Address None

... Show more

Image transcription text

Network Configuration Open the Packet Tracer file attached to this assignment. The network infrastructure is already created with one computer representing each network segment. The network is connected to the web server via the router named East Building Gateway. What you have to do 1. Configure one PC for each of the two departments and one server for the server block with a proper IP address, subnet mask and default gateway. 2. Configure the routers' active interfaces with the appropriate IP addresses (default gateway on the PC side) and subnet masks. Make sure the interfaces are turned on. The serial interface on the East and West building gateway router and the web server are pre- configured and should NOT be modified. 3. Configure RIP routing on all the East building LAN routers (Accounting, Marketing and Server Block). The Gateway is already configured. To do that, select RIP under the config tab and enter the address of the network that should be advertised to all the other routers. Entering the address of the main network (192.168.10.0) is enough. 4. At this stage, you should be able to simulate a Ping from every point inside and outside the LAN. If Pings are successful, continue with the steps below. You may have to wait for a few minutes for all the routers to be synchronized. RIP is slow to converge. 5. On the Accounting Router, go to the Command Line Interface and enter the command "Show IP Route". The routing table should appear. Note: This command must be entered at the privileged level, where the prompt is Router#. If you are not at this level, use the CTRL-Z command to get there or the Enable command if you see a prompt like Router>. 6. Cut and paste the content of the routing table in the box below. Paste the content of the routing table here. 7. Explain the difference between the lines starting with the letter C, R and R*. Enter text here.

... Show more

Image transcription text

iologies 8. On the accounting router table, there is no mention of the segment where the web server is hosted. Explain why and how packets coming from the accounting PC find their way to the web server. Enter text here. 9. What version of RIP is being used? Explain the benefit of using this version? Enter text here.

... Show more

Image transcription text

Server-PT File Server *Router-PI Server Block. Router-PT PC-PT Router-PT Router-PT Gateway West Building Server-PT Web Server Accounting 1 Accounting Gateway East building Router-PT Marketing PC-PT Marketing 1

... Show more

Image transcription text

Gateway East building 0 X Physical Config CLI Attributes GLOBAL A Serial2/0 Settings Port Status On Algorithm Settings Duplex O Full Duplex ROUTING Clock Rate 4000000 Static RIP IP Configuration INTERFACE IPV4 Address 192.168.20.2 FastEthernet0/0 Subnet Mask 255.255.255.252 FastEthernet1/0 Serial2/0 Tx Ring Limit 10 Serial3/0 FastEthernet4/0 FastEthernet5/0

... Show more

Image transcription text

Gateway East building 0 X Physical Config CLI Attributes GLOBAL RIP Routing (v2) Settings Network Algorithm Settings Add ROUTING Static Network Address RIP 192.168.10.0 INTERFACE FastEthernet0/0 FastEthernet1/0 Serial2/0 Serial3/0 FastEthernet4/0 FastEthernet5/0 Remove W

... Show more

Image transcription text

Gateway West Building 0 X Physical Config CLI Attributes GLOBAL A Serial2/0 Settings Port Status On Algorithm Settings Duplex O Full Duplex ROUTING Clock Rate 2000000 Static RIP IP Configuration INTERFACE IPV4 Address 192.168.20.1 FastEthernet0/0 Subnet Mask 255.255.255.252 FastEthernet1/0 Serial2/0 Tx Ring Limit 10 Serial3/0 FastEthernet4/0 FastEthernet5/0

... Show more

Image transcription text

Gateway West Building 0 X Physical Config CLI Attributes GLOBAL FastEthernet0/0 Settings Port Status On Algorithm Settings Bandwidth O 100 Mbps O 10 Mops | Auto ROUTING Duplex O Half Duplex O Full Duplex | Auto Static MAC Address RIP 000A.F3DC.E71B INTERFACE IP Configuration FastEthernet0/0 IPV4 Address 10.0.0.1 FastEthernet1/0 Subnet Mask 255.0.0.0 Serial2/0 Serial3/0 Tx Ring Limit 10 FastEthernet4/0 Fastt thernet5/0

... Show more

Image transcription text

Gateway West Building 0 X Physical Config CLI Attributes GLOBAL RIP Routing (v2) Settings Network Algorithm Settings Add ROUTING Static Network Address RIP 10.0.0.0 INTERFACE FastEthernet0/0 193.0.10.0 FastEthernet1/0 Serial2/0 Serial3/0 FastEthernet4/0 FastEthernet5/0

... Show more

Image transcription text

Web Server 0 X Physical Config Services Desktop Programming Attributes GLOBAL Global Settings Settings Algorithm Settings INTERFACE Display Name Web Server FastEthernetO Gateway/DNS IPV4 O DHCP O Static Default Gateway 10.0.0.1 DNS Server

... Show more

Image transcription text

Web Server 0 X Physical Config Services Desktop Programming Attributes GLOBAL FastEthernet0 Settings Port Status On Algorithm Settings Bandwidth O 100 Mbps O 10 Mops | Auto INTERFACE Duplex Half Duplex O Full Duplex | Auto FastEthernet0 MAC Address 0030.F265.3769 IP Configuration O DHCP O Static IPV4 Address 10.0.0.2 Subnet Mask 255.0.0.0

... Show more